P1000 C-Fab lift Review.

[dukeANhammer]

Finally got around to installing the bumper and 4 inch portals

 

[Hayconpey]

Got my crab kit for my honda how are you all adjusting the lower a-arms for the alignment

 

[dukeANhammer]

Got my crab kit for my honda how are you all adjusting the lower a-arms for the alignment

I eyeballed it after a few min riding around behind the house. Drove it back into the garage on a level surface and adjusted the threaded chromoly helms in or out according to how the tire was sitting.

 

[Hayconpey]

I eyeballed it after a few min riding around behind the house. Drove it back into the garage on a level surface and adjusted the threaded chromoly helms in or out according to how the tire was sitting.

Thanks for the reply. Just noticed my post with auto correct in place wish I would have noticed it before I posted it.

 

[Hayconpey]

Ok put the cfab kit on took it out for a long ride and it has a lot of clunking in the joints the spacers are in and tight nothing loose as far as I can tell. Has anyone else had this problem and if so what can be done to stop the clunking.
Thanks in advance

 

[dukeANhammer]

Ok put the cfab kit on took it out for a long ride and it has a lot of clunking in the joints the spacers are in and tight nothing loose as far as I can tell. Has anyone else had this problem and if so what can be done to stop the clunking.
Thanks in advance

The clunking is in the ball joints? If it’s sitting still can you push the side of the front tire, the side closest to door with your foot, watch and see if there’s any movement where the arms connect to the frame.

 

[chucksmith0706]

Finally got around to installing the bumper and 4 inch portals

View attachment 268247 View attachment 268248 View attachment 268249 View attachment 268250

looks great. Over all how happy with the C fab Arms? I am about to order some arms and really like these have built in lift.

 

[dukeANhammer]

looks great. Over all how happy with the C fab Arms? I am about to order some arms and really like these have built in lift.

I’m satisfied with what i have but i question the pros and cons between the c fab and super atv brand. Before my post above the Honda was run into a tree by one of my teenagers, they were fine but the tabs ripped off the frame and the a arm broke. The guy at c fab replaced it, for $150. Not sure how super atv would’ve handled it. I say that and just remembered, i have the flip up windshield from super atv, one of my gas struts was stolen and to replace through super atv was around $60, got 2 new ones from Amazon for $24 with all mounting hardware.

 

[DennyChapman]

Where did you order from?

Is that Cfab A-arms on your buggy in the pic

 

[Bradley-Thornton]

Is that Cfab A-arms on your buggy in the pic

His look bigger to me they maybe (texas tough customs) Look them up on Facebook.

 

[chucksmith0706]

Those are Cfab’s and he is running portals. I installed Cfab’s on my bike. I absolutely love them.


Sent from my iPhone using Tapatalk

 

[dukeANhammer]

So an update on breakdowns with the portals, c fab lift and 32 inch tires…. Haven’t went riding in over a year, took it out last weekend and bent both tie rods coming down a rocky hill slowly. Moral of the story, upgrade tie rods if you do any front end upgrades.

 

[ToddACimer]

I’m satisfied with what i have but i question the pros and cons between the c fab and super atv brand. Before my post above the Honda was run into a tree by one of my teenagers, they were fine but the tabs ripped off the frame and the a arm broke. The guy at c fab replaced it, for $150. Not sure how super atv would’ve handled it. I say that and just remembered, i have the flip up windshield from super atv, one of my gas struts was stolen and to replace through super atv was around $60, got 2 new ones from Amazon for $24 with all mounting hardware.

SuperATV is very good about warranty.

 

[Bradley-Thornton]

I added some lube to the heim joints besides that C-fabs still doing good. (I do have upgraded tie rods)

 

[dukeANhammer]

I added some lube to the heim joints besides that C-fabs still doing good. (I do have upgraded tie rods)View attachment 356309

I just got some tires that look similar to yours, red dirt road rd8