BOX1

Dirt road fabrication bed extender

G

Grumpygramps

New Member
Jul 7, 2019
11
27
3
Oregon
Ownership

  1. 1000-5
Got new bed extender today. 15 min install and it was on! Dirt road really does a nice job. 32 in tensor regulator fit in the bed but barely. I was hoping that would be the case because I wanted to keep the spare down as low as possible.
85C2707E F8B4 4A07 A9B7 92E401E70B39
0F637449 291C 4DC5 B6F0 7C95F1EE9D9D
7863D01F E717 4ED0 9AA5 018DD7545695
38FBEED7 DD99 4AE6 8937 3CF731FFE067
 
CID

CID

Well-Known Member
Lifetime Member
Supporting Member
Oct 27, 2019
4,975
22,071
113
SE Denver-ish
Ownership

  1. Talon R
Sweet!! I've been looking at those, one of my last add-ons. Could you measure the straight section across the width, plz? I want to mount a 21.25" wide Rotopax across the inside and need to know if it'll fit without running into the corner bends.
 
  • Like
Reactions: Biteme and BWAF
BWAF

BWAF

I get paid to pass gas
Lifetime Member
Jan 24, 2018
8,853
42,410
113
Carthage MO
Ownership

  1. 1000-5
G

Grumpygramps

New Member
Jul 7, 2019
11
27
3
Oregon
Ownership

  1. 1000-5
Sweet!! I've been looking at those, one of my last add-ons. Could you measure the straight section across the width, plz? I want to mount a 21.25" wide Rotopax across the inside and need to know if it'll fit without running into the corner bends.
I’m not sure where ur talking about in the measurement but lm planning on mounting a rotopax gas jug off the left roll bar and a rotopax water jug off the right one. The measurement to the bends in the end gate is 20 inches to the start of the bend. I might mount my 2 jugs off the back of end gate but was concerned about adding more length.
Sweet!! I've been looking at those, one of my last add-ons. Could you measure the straight section across the width, plz? I want to mount a 21.25" wide Rotopax across the inside and need to know if it'll fit without running into the corner bends.
 
  • Like
Reactions: Biteme and BWAF
CID

CID

Well-Known Member
Lifetime Member
Supporting Member
Oct 27, 2019
4,975
22,071
113
SE Denver-ish
Ownership

  1. Talon R
I’m not sure where ur talking about in the measurement but lm planning on mounting a rotopax gas jug off the left roll bar and a rotopax water jug off the right one. The measurement to the bends in the end gate is 20 inches to the start of the bend. I might mount my 2 jugs off the back of end gate but was concerned about adding more length.
20" inside the end gate bends is what I needed to know, thanks. 👍
 
TalonMatt

TalonMatt

Active Member
Jan 9, 2020
64
128
33
WA
Ownership

  1. Talon R
Nice! Been waiting on one and can’t wait.
 
  • Like
Reactions: Biteme
ThunderChicken

ThunderChicken

Active Member
Sep 7, 2019
69
145
33
BATH
Ownership

  1. Talon X
I cant tell from the pictures. does it look like the down tubes would work with bumper mounted. Ive got a HMF rear with hitch coming.
 
  • Like
Reactions: Biteme
CID

CID

Well-Known Member
Lifetime Member
Supporting Member
Oct 27, 2019
4,975
22,071
113
SE Denver-ish
Ownership

  1. Talon R
Just ordered one of these today with a 14-week lead time. Can't wait!

Steve
I love mine, 6k miles without a problem.
 
D

Dankathy

Well-Known Member
May 4, 2020
286
821
93
Utah
Ownership

  1. Talon R
Will the low spare tire mount work with a 6+1 offset (front) wheel?
 
  • Like
Reactions: Biteme
ThunderChicken

ThunderChicken

Active Member
Sep 7, 2019
69
145
33
BATH
Ownership

  1. Talon X
I think I'm finally ready to pull the trigger. I'm still concerned with making it work with my HMF bumper. If anyone has done it please post a picture. I want one bad but i don't want to loose my bumper with the built in hitch.

Recent phone 633
 
  • Like
Reactions: Biteme
CID

CID

Well-Known Member
Lifetime Member
Supporting Member
Oct 27, 2019
4,975
22,071
113
SE Denver-ish
Ownership

  1. Talon R
I think I'm finally ready to pull the trigger. I'm still concerned with making it work with my HMF bumper. If anyone has done it please post a picture. I want one bad but i don't want to lose my bumper with the built in hitch.

View attachment 316273
I think you're SOL. You could always sell the HMF and add a Dragonfire hitch.
1643469794847


1643469868588


1643469944431
 
D

Dirt-roadfab

Well-Known Member
Aug 25, 2018
73
277
53
Utah
Ownership

  1. 1000-5
I know he makes brackets to mount to the honda bumpers. hoping someone had made them work with other bumpers.
I have sent pieces to adapt my extender to the HMF bumper but I don't have a Talon or the HMF bumper to do it myself.
It would be very similiar to the Honda steel bumper setup but with 1.75 clamps. I have attached a picture of the Honda bumper setup.

Received 1224481528016743
 
BOX2
box3

About us

  • Our community has been around for many years and pride ourselves on offering unbiased, critical discussion among people of all different backgrounds. We are working every day to make sure our community is one of the best.

User Menu

Buy us a beer!

  • Lots of time and money has gone into making sure the community is running the best software, best designs, and all the other bells and whistles. Care to buy us a beer? We'd really appreciate it!

    Beer Fund!

    Club Membership!