Robobrainiac
Well-Known Member
Lifetime Member
Thank you for all your information you are super helpful! I appreciate it. I look forward to doing another set. What I made works but it's not as nice as it could have been.
You should see my first couple of attempts haha. I started with trial and error and wasted alot of time and parts tearing them apart and trying better and different things. Only just now learning what works with pvc. Next step is figure out a cheap budget quick disconnect setup. Gonna look into hydraulic hose fittings next
Robobrainiac
Well-Known Member
Lifetime Member
I did round 2 for my whips tonight. Got my new nilight mounts installed and I slightly bent the plate I used to place it slightly back from the ROPS so it had a lean effect to it. We rode into town and trick or treated for a couple hours and rode back. The mounts held up. I like the whips but I am excited to get to redo them and make them better.
Robobrainiac
Well-Known Member
Lifetime Member
It could only spin as far as the secured wire would let it. There wouldn't be any force on it trying to actively twist it around I dont think
Tonights project. Whip sync'd rock lights and grill light for my 4 wheeler.
Last edited:
1st attempt so far so good. Hope they look alright when connected to my whip. 4 6" bars for over each tire and the 12" for behind the grill.
Robobrainiac
Well-Known Member
Lifetime Member
I just ordered the bases you recommended. I will return the tram bases to Amazon. Do you know of a better mount than the nilight mounts? Mine seem like they still move under load like they bounce on the bolts and I feel they will break again.NOOOOOOOOOOOOOOOOOO I totally missed this link, DO NOT USE THAT QUICK RELEASE!!!
The external wings bend if any force gets applied to it... I left those vise grips holding it like that for 6 months before i just recently took it off and bolted my whip straight to the rack.
Try this one instead
Internal CB Radio Antenna Quick Disconnect Mount | eBay
Find many great new & used options and get the best deals for Internal CB Radio Antenna Quick Disconnect Mount at the best online prices at eBay! Free shipping for many products!www.ebay.com
View attachment 232706
Robobrainiac
Well-Known Member
Lifetime Member
Where did you find the clear tube for the rock lights? Do you have a picture of them installed to see how bright they are compared to like the single led mounts.
These i made inside a tube i already had from a few years ago. We bought some cheap ebay whips for our 3 4 wheelers we were running at the time. Just to be a bit flashier than a bike flag the park required for entry.
5 Feet Quick Release ATV UTV LED Light Whip With Flag - 6 Color Available for sale online | eBay
Find many great new & used options and get the best deals for 5 Feet Quick Release ATV UTV LED Light Whip With Flag - 6 Color Available at the best online prices at eBay! Free shipping for many products!
www.ebay.com
End caps
I have this tube coming in today to see if it will work too for another set
Small Parts-TPC-063/10-48 Polycarbonate Tubing, 1/2" ID x 5/8" OD x 1/16" Wall, Clear Color 48" L: Industrial Plastic Tubing: Amazon.com: Industrial & Scientific
Small Parts-TPC-063/10-48 Polycarbonate Tubing, 1/2" ID x 5/8" OD x 1/16" Wall, Clear Color 48" L: Industrial Plastic Tubing: Amazon.com: Industrial & Scientific
www.amazon.com
I had one of these extension cables from the original whips i built so using 3 of the 4 wires it slips right through my end cap by burning a hole in the center with the soldering iron. Filled both end caps with clear silicone before putting them on to seal everything up
LED Extension Wire Cable Cord For RGB Wire 5050 3528 Led Strip Connector 4Pin | eBay
Find many great new & used options and get the best deals for LED Extension Wire Cable Cord For RGB Wire 5050 3528 Led Strip Connector 4Pin at the best online prices at eBay! Free shipping for many products!
www.ebay.com
I have no clue how bright they will be on my wheeler yet as i finished making them at 1:30am last night and haven't got to install em yet
Finished up my rock light project. These are all WS2811 12v led's. Not as bright and crisp as the 5v WS2812B strips but i made the rock lights out of garbage scraps just to see how it would do before throwing them away. 
Robobrainiac
Well-Known Member
Lifetime Member
Those look cool. What controller did you use to get those patterns?
The 120 pattern SP110e Bluetooth I linked in the 1st post.
Adam490
HFA Grand High Wizard
Lifetime Member
Supporting Member
Got my new transformer installed. Confirmed my plugs to the whips were getting the correct 5v output from the transformer and plugged in the whips... only one lit up. Come to find out the negative side inside the factory soldered pigtail on the LED strip was never soldered, so the LED's would never have worked. Should have checked them both from the get go.
TL;DR - Check to be sure your LED strips work before building the whips.
TL;DR - Check to be sure your LED strips work before building the whips.
Amazon strikes again, new delivery today for the next set to come off my work bench. 35mm Fishing rod grip heat shrink is awesome to add a little texture to the top and bottom and seal everything up.
IP65 waterproof WS2812B Eco strip
35mm Clear Heat Shrink
Running it on a 5v 6amp converter. Seems to do alright so far.
Amazon.com : Weilan 35mm X-Tube Heat Shrink Sleeve Wrap Tubing for Fishing Rod Grips with Non Slip Waterproof and Insulation Lengths Durable Repair39(1M, Black) : Sports & Outdoors
Amazon.com : Weilan 35mm X-Tube Heat Shrink Sleeve Wrap Tubing for Fishing Rod Grips with Non Slip Waterproof and Insulation Lengths Durable Repair39(1M, Black) : Sports & Outdoors
www.amazon.com
IP65 waterproof WS2812B Eco strip
35mm Clear Heat Shrink
Running it on a 5v 6amp converter. Seems to do alright so far.
Similar threads
P1000m3
DIY Bed Rack
P1000
Personalizing my P1000-5
- old sparky
- Pioneer 1000 Accessories and Modifications 2