P1000 General Accessories Question

M

Markbama

Member
Nov 27, 2015
30
12
8
Millbrook AL
Ownership

  1. 1000-5
All,

I have been lurking on this forum for awhile now...I finally pulled the trigger, I am picking up my 1000-5, silver in Chattanooga this saturday. I know I want a roof, a windshield and skid plates, arm protectors immediately. So my question is aboyt the skid plates, can you put them on without a lift? Is there some lift hacks I may be able to use...that I am not aware of?

I am nervous and excited...never spent this kind of money and I don't want to muck it up...

cheers
 
  • Like
Reactions: Stauvo and Crow_Hunter
Crow_Hunter

Crow_Hunter

Well-Known Member
May 18, 2016
750
836
93
Riding a Canned Ham.
Ownership

  1. Do not currently own
Markbama said:
All,

I have been lurking on this forum for awhile now...I finally pulled the trigger, I am picking up my 1000-5, silver in Chattanooga this saturday. I know I want a roof, a windshield and skid plates, arm protectors immediately. So my question is aboyt the skid plates, can you put them on without a lift? Is there some lift hacks I may be able to use...that I am not aware of?

I am nervous and excited...never spent this kind of money and I don't want to muck it up...

cheers
Click to expand...

All you guys and your Silver machines.... :) (That is what I really wanted but couldn't wait)

I would wait on the windshield until you get it and drive it, you can always buy it later. The machine is pretty hot as is and from what I have read on here the windshield makes it worse. I test drove a P1000-3 with a windshield/roof and hard back panel and it noticeably pulled warm air up into the cabin area.

While I like the Honda rear A-arm protectors quite a bit, I am not as much of a fan of the front. I think they could have done a better job of protecting the front CV boot and if I could do it over again, I would probably look much closer at getting an aftermarket set.

I am not sure about the skid plate assembly since I personally don't have them but I have seen where people used their winch to lift the front of the machine and put it on blocks.

Don't get the Honda skid plate though. It only protects what the factory (plastic) skid plates cover now and leaves the sides open/unprotected.

I am planning on getting one eventually and I looked at the Honda one because it was cheaper and I found out it is because it doesn't cover all of the bottom of the machine.
 
Delton

Delton

Honda Fanboy
Vendor
Lifetime Member
Club Contributor
Jan 6, 2016
9,967
31,488
113
Middle TN
Ownership

  1. 1000-5
I can't remember if I had the lift on mine when I installed the skid or not, but even without a lift, I could install it without raising machine. It's tight under there but that's actually a good thing. I played each piece on my stomach and slid it in place. Having a gut like me helps lol.
 
  • Like
Reactions: Stauvo, whayden2003, vince and 1 other person
sugarray

sugarray

Is this a game show?
Lifetime Member
Feb 17, 2016
661
1,257
93
WV
Ownership

  1. 1000-5
I just put my front tires on ramps I use for changing oil in my wife's Honda Pilot. Worked well.
 
AKRider

AKRider

Well-Known Member
Lifetime Member
Supporting Member
Club Contributor
Mar 31, 2016
1,402
3,224
113
Palmer, Alaska
Ownership

  1. 1000-5
I put mine up on 4 ramps. Works good for oil changes, too.

Like this...


20160702 012939
 
joeymt33

joeymt33

i4WD=imitated 4WD
Moderator
Lifetime Member
Supporting Member
Club Contributor
Mar 17, 2015
11,096
39,129
113
Guntersville, AL
Ownership

  1. 1000-3

  2. 1000-5
Markbama said:
All,

I have been lurking on this forum for awhile now...I finally pulled the trigger, I am picking up my 1000-5, silver in Chattanooga this saturday. I know I want a roof, a windshield and skid plates, arm protectors immediately. So my question is aboyt the skid plates, can you put them on without a lift? Is there some lift hacks I may be able to use...that I am not aware of?

I am nervous and excited...never spent this kind of money and I don't want to muck it up...

cheers
Click to expand...


How close are you to Guntersville? We could install those skids rather quickly if we team up. I guess this kind of lift helps too....

750b1a9071642ef0badd40e38bda2de3
 
  • Like
Reactions: pct and Crow_Hunter
joeymt33

joeymt33

i4WD=imitated 4WD
Moderator
Lifetime Member
Supporting Member
Club Contributor
Mar 17, 2015
11,096
39,129
113
Guntersville, AL
Ownership

  1. 1000-3

  2. 1000-5
It may not be that bad if you have your skid plates with you when you're bringing your pioneer back down south.

Other than that, some people winch theirs into a tree or winch it over sideways to help gain access. Just always use safety strap if you are suspending the vehicle.
 
  • Like
Reactions: pct
M

Markbama

Member
Nov 27, 2015
30
12
8
Millbrook AL
Ownership

  1. 1000-5
joeymt33 said:
It may not be that bad if you have your skid plates with you when you're bringing your pioneer back down south.

Other than that, some people winch theirs into a tree or winch it over sideways to help gain access. Just always use safety strap if you are suspending the vehicle.
Click to expand...

I thought of that...I won't have them unforturnately...I think I may have a solution...but if that falls through I may just take you up on your offer. I have driven a lot further for alot less...lol! Plus I get to meet a fellow pioneer rider...
 
  • Like
Reactions: ChadMarti, Delton and joeymt33
Delton

Delton

Honda Fanboy
Vendor
Lifetime Member
Club Contributor
Jan 6, 2016
9,967
31,488
113
Middle TN
Ownership

  1. 1000-5
Markbama said:
I thought of that...I won't have them unforturnately...I think I may have a solution...but if that falls through I may just take you up on your offer. I have driven a lot further for alot less...lol! Plus I get to meet a fellow pioneer rider...
Click to expand...
Drive down/up and meet him. He's a helluva nice guy and very knowledgeable bout these things. Can't beat him with a stick.
 
  • Like
Reactions: pct and joeymt33
advertisement
Delton

Delton

Honda Fanboy
Vendor
Lifetime Member
Club Contributor
Jan 6, 2016
9,967
31,488
113
Middle TN
Ownership

  1. 1000-5
sugarray said:
I just put my front tires on ramps I use for changing oil in my wife's Honda Pilot. Worked well.
Click to expand...
I've got a set of those, don't now why I didn't use them. I figured if I can slide TH350s into place using my belly, a skid plate wouldn't be a big deal lol
 
  • Like
Reactions: pct and joeymt33
KevinSC

KevinSC

Well-Known Member
Dec 31, 2015
286
306
63
Delton said:
I've got a set of those, don't now why I didn't use them. I figured if I can slide TH350s into place using my belly, a skid plate wouldn't be a big deal lol
Click to expand...
If you would have bought a FORD, you wouldn't have to do that :p
 
  • Like
Reactions: Delton and joeymt33
tjoreo

tjoreo

Well-Known Member
Lifetime Member
Feb 18, 2015
1,025
1,975
113
Southern Idaho
Ownership

  1. 1000-5
Take a look at @JACKAL 1000 build. He shows the proper way to install the skid plate. He has a good point on installing it though, and that it should be the first thing you put on before you get the rig too muddy.
 
  • Like
Reactions: joeymt33
M

Markbama

Member
Nov 27, 2015
30
12
8
Millbrook AL
Ownership

  1. 1000-5
tjoreo said:
Take a look at @JACKAL 1000 build. He shows the proper way to install the skid plate. He has a good point on installing it though, and that it should be the first thing you put on before you get the rig too muddy.
Click to expand...

Yeah I have had a man crush on JACKALs builds for some time now...
 
  • Like
Reactions: joeymt33
joeymt33

joeymt33

i4WD=imitated 4WD
Moderator
Lifetime Member
Supporting Member
Club Contributor
Mar 17, 2015
11,096
39,129
113
Guntersville, AL
Ownership

  1. 1000-3

  2. 1000-5
Delton said:
Nothing but love for ya man!
Click to expand...

Actually, I've got to pull the rear differential again and install a new seal. I need to find someone that needs some work on their pioneer and trade off the labor.

I'll just keep my knife on my hip, just in case.

Ed5919fc36c98825fc23ae0302fd5d35
 
  • Like
Reactions: pct and sharp
You must log in or register to reply here.

Similar threads

Bucks
P1000 Dual battery question
Replies
8
Views
404
Pioneer 1000 Accessories and Modifications
DRZRon1
DRZRon1
540RA
P1000 2023 speedometer calibrator wiring question...
Replies
19
Views
592
Pioneer 1000 Accessories and Modifications
Jankyeye
Jankyeye
P
P1000 Momentary switch and dual volt meter question.
Replies
16
Views
610
Pioneer 1000 Accessories and Modifications
Proff49
P
T
P1000 Rookie question about dual battery and sound bar
Replies
3
Views
568
Pioneer 1000 Accessories and Modifications
Remington
Remington
540RA
P1000 Added some Ka-Bar accessories.
Replies
2
Views
692
Pioneer 1000 Accessories and Modifications
540RA
540RA

About us

  • Our community has been around for many years and pride ourselves on offering unbiased, critical discussion among people of all different backgrounds. We are working every day to make sure our community is one of the best.

User Menu

Login

Share this page

Share this page

Buy us a beer!

  • Lots of time and money has gone into making sure the community is running the best software, best designs, and all the other bells and whistles. Care to buy us a beer? We'd really appreciate it!

    Beer Fund!

    Club Membership!

©2013-2020 HondaSxS.com, Honda SxS Club | 2FarOffRoad LLC - 2FarOffRoad.com
HondaSxS.com is not affiliated with Honda Motor Co Ltd | Honda, Honda Pioneer, Honda Talon are registered trademarks of Honda Motor Co., Ltd.
We are a participant in the Amazon Services LLC Associates Program and eBay Inc Affiliate Program. Both of which are affiliate advertising program designed to provide a means for us to earn fees by linking to said affiliated sites.
Top Bottom