P1000 Rear Spring Spacer...HELP!

[DanDan]

2018 P1K5D. I was smart enough to install the front spring spacers.
I am not smart enough to figure out the steps for installing the rear spring spacers.
Please, can someone tell me the detailed step by step process for installing the rear spacers? Do not underestimate the value in adding/describing a step that even a moron should know or be able to figure out. Thanking in advance.

 

[Admin]

 

[Russ989]

2018 P1K5D. I was smart enough to install the front spring spacers.
I am not smart enough to figure out the steps for installing the rear spring spacers.
Please, can someone tell me the detailed step by step process for installing the rear spacers? Do not underestimate the value in adding/describing a step that even a moron should know or be able to figure out. Thanking in advance.

Honda Pioneer 1000-5 lift kit

 

[DanDan]

Honda Pioneer 1000-5 lift kit

Russ.....thank you so much. I'm struggling with removing the rear shocks. I have been unable to relieve enough pressure on either of the shock bolts in order to remove them.

 

[Russ989]

Russ.....thank you so much. I'm struggling with removing the rear shocks. I have been unable to relieve enough pressure on either of the shock bolts in order to remove them.

Take the tire off after you jack it up, that should help take the pressure off of it.

 

[Russ989]

Russ.....thank you so much. I'm struggling with removing the rear shocks. I have been unable to relieve enough pressure on either of the shock bolts in order to remove them.

You might have to take a rubber mallet and give them a tap.

 

[DanDan]

10-4. I'll give it a shot tomorrow after work. Will let you know how it works out. Your video was very helpful, too.

 

[Russ989]

10-4. I'll give it a shot tomorrow after work. Will let you know how it works out. Your video was very helpful, too.

Good deal, glad to be of some help.

 

[DanDan]

You might have to take a rubber mallet and give them a tap.

Russ....after building fence all week, I got around to the rear shock spacers today. Do you remember what inch ID the rear pipe is? For some reason the shop cut me pipe that is 2.5"ID. Is that correct?

 

[Russ989]

Russ....after building fence all week, I got around to the rear shock spacers today. Do you remember what inch ID the rear pipe is? For some reason the shop cut me pipe that is 2.5"ID. Is that correct?

Let me look in a minute, I’ll have an extra set of rear spacers on the bench in the garage.

 

[Russ989]

Russ....after building fence all week, I got around to the rear shock spacers today. Do you remember what inch ID the rear pipe is? For some reason the shop cut me pipe that is 2.5"ID. Is that correct?

Looks like 3 1/16”

 

[DanDan]

Thanks. You've come to the rescue again!

 

[Russ989]

Thanks. You've come to the rescue again!

No problem

 

[DanDan]

No problem

Russ...got the spacers on a couple of weeks ago. My spacers are .75 in length. I forgot to measure the height increase prior to putting them on the rig. What length is yours and do you know the added height? Thanking you in advance.

 

[Russ989]

Russ...got the spacers on a couple of weeks ago. My spacers are .75 in length. I forgot to measure the height increase prior to putting them on the rig. What length is yours and do you know the added height? Thanking you in advance.

If memory serves me right, you should gain double the spacer. So you .75 should have lifted your rig right under 1.5 inches.

 

[DanDan]

If memory serves me right, you should gain double the spacer. So you .75 should have lifted your rig right under 1.5 inches.

As always, thanks a bunch.

 

[tdhanses]

Honda Pioneer 1000-5 lift kit

Where do you get this lift or is it a home made option?

 

[Adam490]

Where do you get this lift or is it a home made option?

Those are home made spacers cut from pipe.

 

[Russ989]

Those are home made spacers cut from pipe.

Thanks Adam

 

[DanDan]

My pipe was cut at .75 inches. If I were to do it over, I would prolly have em cut at 1 inch.

 

[CGD]

I had a friend cut mine at 1-1/8" on his lathe for the front and 1" for the rear. I had him cut extra so we can lift the P700 that we bought for the kids also.