BOX1

P700 Winching point in front of 700

G

Gizzy_44

Member
Feb 1, 2021
24
31
13
Duhamel, Quebec
Ownership

  1. 700-2
Just got my new 2021 700-2
i added the Honda warn winch

question:
Where do you hook up to tow vehicle in the front ?
Are there any D rings or hooks that mount on front for recovery?

thanx
 
  • Like
Reactions: Mudwing
Glock21user

Glock21user

" Nothing succeeds like excess "
Lifetime Member
Dec 16, 2018
1,807
8,976
113
Livingston county, Mi.
Ownership

  1. 700-4
They are difficult to come by on these machines unless you use a short tree saver strap and get around a tube on the frame or a lower control arm in a pinch.
Whatever you do never ever ever wrap around two tubes of anything and try to pull.
The forces of pulling can collapse them together at worst or bend them at best.
 
  • Like
Reactions: Mudwing
insanetreefrog

insanetreefrog

Active Member
Nov 19, 2020
51
140
33
Lowell, AR
Ownership

  1. 700-4
I've had pretty good success using my front receiver mount with a shackle installed. Providers a good point to come back from a snatch block and "double up" your winch power.

PXL 20210331 235300422 PXL 20210331 235314707
 
insanetreefrog

insanetreefrog

Active Member
Nov 19, 2020
51
140
33
Lowell, AR
Ownership

  1. 700-4
Yes sir. Wasn't bad stuck and could've gotten out with a single line, but to be honest I wanted to use my snatch block and all to get out
 
  • Like
Reactions: Buckshot07
Buckshot07

Buckshot07

Well-Known Member
Dec 31, 2020
19,159
198,159
113
PA
Ownership

  1. 700-4
Yes sir. Wasn't bad stuck and could've gotten out with a single line, but to be honest I wanted to use my snatch block and all to get out
I have to get a different 5/8 hitch pin or fabricate one from a bolt to use mine. All of mine are on a 45 and contact the winch mount before going through the receiver mount.
 
  • Like
Reactions: Backwoods
Buckshot07

Buckshot07

Well-Known Member
Dec 31, 2020
19,159
198,159
113
PA
Ownership

  1. 700-4
Is the 2” receiver home made?
Ive just looked on Amazon and did not see one with bolting brackets on sides
It is a KFI front 2” receiver. Will work if you have a winch mount in which your winch is mounted underneath.
 
  • Like
Reactions: Mudwing
insanetreefrog

insanetreefrog

Active Member
Nov 19, 2020
51
140
33
Lowell, AR
Ownership

  1. 700-4
I have to get a different 5/8 hitch pin or fabricate one from a bolt to use mine. All of mine are on a 45 and contact the winch mount before going through the receiver mount.
Had the same problem. I cut about an inch or so off one of mine, and that made it fit. Then I just drilled a new hole for the pin and it was good to go.
 
BigEarlX4

BigEarlX4

Member
Jul 23, 2020
21
75
13
St. Helen, MI
Ownership

  1. 700-4

  2. Talon X4 LV
I ordered a couple weldable tubing clamps, took a piece of steel, angled the ends to fit the clamps, then welded them up and then welded a clevis tab on. Took a couple hours and works great.

20201203 121228 HDR 2
 
Gator

Gator

The Most Unknown Member
Lifetime Member
Sep 16, 2015
2,468
10,325
113
Louisiana
Ownership

  1. 700-2
I just hook my winch to their winch.
 
  • Like
Reactions: Mudwing
BOX2
box3

About us

  • Our community has been around for many years and pride ourselves on offering unbiased, critical discussion among people of all different backgrounds. We are working every day to make sure our community is one of the best.

User Menu

Buy us a beer!

  • Lots of time and money has gone into making sure the community is running the best software, best designs, and all the other bells and whistles. Care to buy us a beer? We'd really appreciate it!

    Beer Fund!

    Club Membership!