P1000 Honda Pioneer 1000 Oil Change Guide!

[Hondasxs]

Can't get any of these links to work. This thread still operating?

Which link?
Checked a few and they all work.

Sent from my SM-G955U using Tapatalk

 

[Admin]

 

[JACKAL]

Which link?
Checked a few and they all work.

Sent from my SM-G955U using Tapatalk

Ditto, just checking several myself. They all work for me too.

 

[JEP]

Alright, I would like to know how many of us had to use more than the 6.1-6.2 quarts to reach the top of the full level on the dipstick? Because I am at about 6.3(6 quarts, 9 ounces) and just at the bottom of the dipstick. I had to walk away. Going to wait 15 minutes and go check it again.

 

[Tundra20]

Did u crank it up let it run for a minute once u hit the 6.1 mark let it set then go back recheck mine was spot on at 6.1 im sure u have done this but check for leaks at drain plug

 

[JEP]

Did u crank it up let it run for a minute once u hit the 6.1 mark let it set then go back recheck mine was spot on at 6.1 im sure u have done this but check for leaks at drain plug

I did. 6.3 made it to the full line.

Walked away. Ate lunch came back 30 minutes later and it measured full. Guess you just have to wait a bit for the oil to drain back in for a accurate measurement

 

[Tundra20]

U got it

 

[JEP]

Thanks for getting back to me.

Are you a Tundra guy too? As soon as I am done servicing the Pioneer, I am bringing my Tundra in for a wash. I saw this morning they are finally working on a new engine to get better gas mileage. Going the Ford route, V6 with turbos.

 

[JTW]

Alright, I would like to know how many of us had to use more than the 6.1-6.2 quarts to reach the top of the full level on the dipstick? Because I am at about 6.3(6 quarts, 9 ounces) and just at the bottom of the dipstick. I had to walk away. Going to wait 15 minutes and go check it again.

I was like you just a couple weeks ago... I was careful to measure it all out. Followed the procedure half a dozen times and was like WTF?? Talked to several guys and everyone said theirs held more too!

 

[Tundra20]

Going the Ford route, V6 with turbos.

Ya I’m tundra fella I love mine does everything I need it to but yes gas mileage stinks but I didn’t buy it for fuel mileage

 

[russknight]

Is anyone using any engine / transmission other oil than Honda? Anyone running Amzoil? What is everyone running in the diffs?

 

[Tundra20]

Idk but good question i will be watching this

 

[CumminsPusher]

@BlackHawk328

 

[russknight]

I’m running 20w-50. Seems to have smoothed the shift a little, still noisy as hell.

 

[nelson1033]

Special thanks to @JACKAL for helping put this together and providing the detailed images.

Also wish to thank @MAINEYAK for the video guide below.

Helped a bunch. Thanks for the video

 

[Rickyjo09]

Getting ready to do my first oil change. Thanks for the info. Very helpful.

 

[solrus]

WARNING!!!!
PLEASE USE APPROPRIATE TOOLS TO TORQUE TO SPECS THOSE OIL FILTER COVER BOLTS.
My neighbor got new p1000 and said he wanted to do it like pro mechanic and had only this 1/2 torque wrench that starts with 10 ftlb , he thought by twisting the dial lower he can lower torque effort . He bended/twisted 2 out of 3 bolts and decapitated the third bolt. He blamed our forum guy on the video who said that specs are 9 ftlb instead.

But I told him that he used light house grown big cucumber to f... small rabbit instead of using baby carrot (((. Sorry. I was mad at him not even asking if doubt.
I said get left handed easy out bits , he got them. I told wait for me, im back from work in 4 hours, instead he found leather punch not metal punch, did not punch properly and started to drill the broken bolt and went towards engine housing , the hole looks like triangle now, bolt still there . I'm pissed now. And told him to take it to dealer , bc the engine needs to come off, its not possible to do anything since space is limited and direction changed .

Please send a pics of your tools to your friends who have more experience with such type of work versus trying to continue to screw up more and have costly repairs . Don't fffff rabbit with cucumbers )).

 

[ohanacreek]

WARNING!!!!
PLEASE USE APPROPRIATE TOOLS TO TORQUE TO SPECS THOSE OIL FILTER COVER BOLTS.
My neighbor got new p1000 and said he wanted to do it like pro mechanic and had only this 1/2 torque wrench that starts with 10 ftlb , he thought by twisting the dial lower he can lower torque effort . He bended/twisted 2 out of 3 bolts and decapitated the third bolt. He blamed our forum guy on the video who said that specs are 9 ftlb instead.

But I told him that he used light house grown big cucumber to f... small rabbit instead of using baby carrot (((. Sorry. I was mad at him not even asking if doubt.
I said get left handed easy out bits , he got them. I told wait for me, im back from work in 4 hours, instead he found leather punch not metal punch, did not punch properly and started to drill the broken bolt and went towards engine housing , the hole looks like triangle now, bolt still there . I'm pissed now. And told him to take it to dealer , bc the engineView attachment 206666View attachment 206667View attachment 206668 needs to come off, its not possible to do anything since space is limited and direction changed .

Please send a pics of your tools to your friends who have more experience with such type of work versus trying to continue to screw up more and have costly repairs . Don't fffff rabbit with cucumbers )).

It’s also the NMeter spec NOT the Lbft spec manual has a typo.

 

[solrus]

It’s also the NMeter spec NOT the Lbft spec manual has a typo.

9 nm??

Sent from my SM-G986U using Tapatalk

 

[ohanacreek]

9 nm??

Sent from my SM-G986U using Tapatalk

Yes 9nm instead of (12nm/9lbft) which is less than 9lbft

 

[solrus]

Yes 9nm instead of (12nm/9lbft) which is less than 9lbft

I told him just you your hand , I do t know why I'm so mad now , .at be bc I found this pioneer for him and he is raping it now brutally ))

It hurts to see those holes and damaged bolts

Sent from my SM-G986U using Tapatalk