P500 Any good pillar light mounts for the P5?

[The Green Goat]

So I'm looking to get rid of my roof-mounted light bar. It flops too much for my liking. Ideally, I'd like to put a couple pod lights down lower; I think at the bottom of the pillars near the hood. I did a quick Amazon search, but that stuff all looks like junk.

Anyone with experience with this?

 

[Admin]

 

[Scrappapotamus]

Check out Axia Alloys. Mounted ditch pods on the roll cage with these. I'm pretty sure your P1K5 uses 1.75 clamps

 

[futzin]

We toyed briefly with using cubes mounted there with Honda clamps.
Did a dry fit; should work.
Probably better ways though. Not my forte...

 

[futzin]

I'll see if I can find a pic or two.
@KyGal83 may have them too.

 

[futzin]

 

[trigger]

I've had good luck with Rough Country stuff. Kinda middle of the road on the price scale.

 

[KyGal83]

I'll see if I can find a pic or two.
@KyGal83 may have them too.

I still wanna do this. With my ROPS now positioned correctly we should be able.

 

[Remington]

Have had good luck with these on all my machines
Light Bar Mounts 1.75 inch Tube Clamp Adjustable LED Light Mounting Clamps Roll Bar Clamps for Truck UTV ATV RZR, Black, Pack of 2 https://www.amazon.com/dp/B0C2KPGR5N?tag=sxsweb24-20

 

[Bighat]

I haven't got pillar lights yet, the buget has went in another direction but I really like the Baja Designs. They're a little top heavy$$$ but they make some good lights. Made in the USA. I did by a light for backup and to see in the dump bed at night from Sylvania. You should check out Sylvania offroad lights. I like the flood I bought. Looks to be built nice and heavy.

LED Off Road Lights

Explore SYLVANIA’s high-performance LED off road lightbars and pods for any adventure. From compact Slim Series to Rugged Tough off road design and high-output Ultra Series, enjoy superior visibility, durability and a lifetime limited warranty.

www.sylvania-automotive.com

Here's the flood I bought: SYLVANIA Dual Mode 6 Inch LED Light Bar - Flood

As for mounts, I looked at many of them when I was thinking about adding pillar lights but for my setup all of them would need to be modified to fit the way I want. I think you could just about use any mount that was close to what you wanted and if you have to dig in the scrap pile or go the hardware and add a piece to them and get what you really want or need. Amazon had a huge selection.

 

[idiggplants]

I'm trying to tackle this job this weekend actually... Was planning on fabricating a sheet metal bracket that would attach using that bolt between the a pillar and the hood exoskeleton(not sure what its called). Only way I can see that it won't interfere with my windshield without modification as most clamps are way too thick

 

[The Green Goat]

I'm trying to tackle this job this weekend actually... Was planning on fabricating a sheet metal bracket that would attach using that bolt between the a pillar and the hood exoskeleton(not sure what its called). Only way I can see that it won't interfere with my windshield without modification as most clamps are way too thick

Yea, I was eyeballing that bolt as well. I bought these on Slamazon to see if I can make it work.

Looks like I might have to enlarge the hole a little but so long as it doesn't rotate, I think it should work. They other option I was looking at was using one of the mounting bolts for my UTV801 windshield. I also think that would work well, but its a smidge higher than I would like though notably more inboard on the position.

I bought Diode Dynamics SS3's, and would love a set of those Axia Alloys, but I'm not dropping nearly $100 on just mounts. They're nice, but they ain't that nice.