P1000 Homemade snorkel

[Adam490]

$27 and she's save up to the back of the seat

View attachment 217980 View attachment 217981

Nice job. My wife or my father who ride in the passenger seat would absolutely hate that though. You may want to add a small filter of some sort if you run a full windshield since a ton of dust comes into that area.

 

[Adam490]

View attachment 217950View attachment 217951
this is my setup, 1: 2 3/4” to 3” silicone adapter 1: 3” piece of pipe from a cold air intake and 1: 90 deg snorkel top.

Take a heatgun and a screwdriver handle to the little dimples/ridges on the inside that keeps the snorkel head from going all the way down. It'll let you put that snorkel head a little lower.

 

[SuperMidget]

Nice job. My wife or my father who ride in the passenger seat would absolutely hate that though. You may want to add a small filter of some sort if you run a full windshield since a ton of dust comes into that area.

No windshield. Just a soft top she will throw on if its going to rain while were out. She prefers the open air feeling

Why would they hate it? It changes nothing about the ride and I don't think the sound would be any different than a under hood snorkel thats right in your face.

 

[Adam490]

No windshield. Just a soft top she will throw on if its going to rain while were out. She prefers the open air feeling

Why would they hate it? It changes nothing about the ride and I don't think the sound would be any different than a under hood snorkel thats right in your face.

Because it would be right in their ear

 

[SuperMidget]

Because it would be right in their ear

with the angle it points it is barely noticeable to me when i ride with her. This was cruising down the road at Muddy Bottoms. The soft top was still on at this time also, we took it off about 20 minutes later.

 

[russknight]

with the angle it points it is barely noticeable to me when i ride with her. This was cruising down the road at Muddy Bottoms. The soft top was still on at this time also, we took it off about 20 minutes later.

Looks like fun!!! Where is that?

 

[SuperMidget]

Looks like fun!!! Where is that?

Muddy Bottoms Offroad park in Louisiana

 

[Mvalerio89]

I routed mine through the passenger side cup holder hole. All 2" SCH40 PVC.

5 x 45 degree elbows
3 x 90 degree elbows
1 x silicone adapter
2 x hose clamps
and a 10' piece of 2" PVC should do it.

View attachment 198958View attachment 198962View attachment 198961View attachment 198960View attachment 198959

I bought the same pvc set up for my 2021 P1K5. I’m going to attempt to make it myself. How did you secure the pvc 45 degree into the intake? I bought a silicone adapter (2 1/2 x 3) but doesn’t seem sturdy enough to keep water out. Any information would be appreciated!

 

[Robobrainiac]

Here's what I have.

View attachment 198407

Do you have a write-up of your snorkel build? Thank you in advance!

Nevermind I found it. Thank you!

 

[Ridinfool]

Do you have a write-up of your snorkel build? Thank you in advance!

Check out his build thread, lots of great ideas.

 

[ToddACimer]

Check out his build thread, lots of great ideas.

Just a combination of a few good ideas and all the stuff everybody else has

 

[Alaska350]

$27 and she's save up to the back of the seat

View attachment 217980 View attachment 217981

What size pvc did you use here?

 

[Jas sxs]

Quick, easy and cheap! Figured the middle is the best location for a snorkel since you usually End up sideways is a Deep mud hole.

View attachment 217947 View attachment 217948 View attachment 217949that's very clean what parts did you use

 

[Remington]

@Jas sxs that guy hasn't been on in 9 months. You're probably better off to go to post number 17 and do it that way that's what mine is like and he has a list of materials for it

 

[Dasmoeturhead]

Here's my snorkel, made up of parts I had lying around the shop . I don't use the cup holders.