Custom Switch Panels for P700 & P1000

[mystic1219]

I have started making custom laser cut and powder coated switch panels to replace the factory warning label on the dash for the 700 and 1000s. I use Carling Contura swtiches from OTRATTW.net but some others may fit. I have also made some to accept a 12v outlet, dual usb charging port or a volt meter. Another option is for a RAM mount to hold a cell phone, gps, go pro or just about anything. I have made them for a Jensen marine radio and an SSV radio controller. Below are pictures of my pioneer and some other guys from facebook that have installed my panels. I work in a metal shop and cut these when we are slow. My price goes up significantly for small runs so I prefer to get several together and cut all at once to keep the costs down. I plan to place and order later this week (by 12-2-15) and will hopefully ship them out by next week. If you miss this order I can always cut more down the road. Let me know what you would like to see! Price is $25 shipped or $20 ea if you order 2 or more.

 

[Admin]

 

[Hondasxs]

Kool. I like the options.
Was looking at the ram mount. But I may also need the Jensen radio in the future.

 

[mystic1219]

Kool. I like the options.
Was looking at the ram mount. But I may also need the Jensen radio in the future.

You could do both... I think 2 rows of 2 switches would fit in there also without being too crowded.

 

[mystic1219]

Now available for the p500 also

 

[Johnny_C]

I just ordered 10 switches from OTTR today.
I hope I can fit 2 rows of 5 in the upper
storage/cubby hole on my P1k. Anyone
have any input on if that will work?

Or, I guess I can put it the switch panel
where the decal is. How much would
that panel cost?

Thanks!

John

 

[mystic1219]

I don't have the measurements yet to make a panel for the far right opening but I charge $25 shipped for the warning label plates any way you want them

 

[Johnny_C]

How soon could I get a matching black
one from you? For the warning label
location. 2 rows of 5 for OTR switches,
centered.

Thanks!

John

I don't have the measurements yet to make a panel for the far right opening but I charge $25 shipped for the warning label plates any way you want them

 

[mystic1219]

I should have enough orders for me to put in an order sometime this week. (If I order less than 10 my price nearly doubles so I try to wait until I have 10). We are a large laser shop and do work for snap-on, wal-mart, Harley-Davidson etc. If we get real busy it could take them up to a couple weeks to get to the plates. However we have been slow and I expect them to move pretty quick I just like to let people know it may take longer. I will add yours to my cut list. Thanks!

 

[Johnny_C]

Ok. I'll take it whenever you get it.

How do I pay you?

Thanks!

John

 

[mystic1219]

You can paypal $25 to [email protected] either now or when it's ready. If you'd rather mail a payment let me know.

 

[Johnny_C]

Paypal works for me.

Thanks!

John

 

[Johnny_C]

Paypal sent!

John

 

[Tot]

I'm liking the one on the bottom right with the 5 switches and the 4 screw holes.

I have started making custom laser cut and powder coated switch panels to replace the factory warning label on the dash for the 700 and 1000s. I use Carling Contura swtiches from OTRATTW.net but some others may fit. I have also made some to accept a 12v outlet, dual usb charging port or a volt meter. Another option is for a RAM mount to hold a cell phone, gps, go pro or just about anything. I have made them for a Jensen marine radio and an SSV radio controller. Below are pictures of my pioneer and some other guys from facebook that have installed my panels. I work in a metal shop and cut these when we are slow. My price goes up significantly for small runs so I prefer to get several together and cut all at once to keep the costs down. I plan to place and order later this week (by 12-2-15) and will hopefully ship them out by next week. If you miss this order I can always cut more down the road. Let me know what you would like to see! Price is $25 shipped or $20 ea if you order 2 or more.
View attachment 7977 View attachment 7978 View attachment 7979 View attachment 7980 View attachment 7981

 

[mystic1219]

Sending you a pm Tot

 

[mystic1219]

Here is what I currently have in stock

 

[legend]

I have started making custom laser cut and powder coated switch panels to replace the factory warning label on the dash for the 700 and 1000s. I use Carling Contura swtiches from OTRATTW.net but some others may fit. I have also made some to accept a 12v outlet, dual usb charging port or a volt meter. Another option is for a RAM mount to hold a cell phone, gps, go pro or just about anything. I have made them for a Jensen marine radio and an SSV radio controller. Below are pictures of my pioneer and some other guys from facebook that have installed my panels. I work in a metal shop and cut these when we are slow. My price goes up significantly for small runs so I prefer to get several together and cut all at once to keep the costs down. I plan to place and order later this week (by 12-2-15) and will hopefully ship them out by next week. If you miss this order I can always cut more down the road. Let me know what you would like to see! Price is $25 shipped or $20 ea if you order 2 or more.
View attachment 7977 View attachment 7978 View attachment 7979 View attachment 7980 View attachment 7981

I would like one for my 700-2 just a strit across 6 hole one do you have the switches also.

 

[mystic1219]

I would like one for my 700-2 just a strit across 6 hole one do you have the switches also.

I only make the panels. I use switches from otrattw.net they are top quality and very customizable. They run about $15 each. Amazon has some generic ones for about half that price that work fine.

 

[Tramguage1]

Do you have any orders for another run? I would be interested in one. Also wonder if the 500 plate will fit the passenger side dash pocket in the 700.

 

[mystic1219]

I'm getting orders pretty quick for another run. I have several left, what are you looking for? The p500 panel does not fit the P700 pocket.

 

[Tramguage1]

I'm getting orders pretty quick for another run. I have several left, what are you looking for? The p500 panel does not fit the P700 pocket.

A couple of the 700 plates. What size is the small round hole? Is it entened for the round 12v plug or the round volt meter that's out there?