Custom Switch Panels for P700 & P1000

Status
Not open for further replies.
mystic1219

mystic1219

Active Member
Vendor
Lifetime Member
Jul 3, 2015
191
202
43
I have started making custom laser cut and powder coated switch panels to replace the factory warning label on the dash for the 700 and 1000s. I use Carling Contura swtiches from OTRATTW.net but some others may fit. I have also made some to accept a 12v outlet, dual usb charging port or a volt meter. Another option is for a RAM mount to hold a cell phone, gps, go pro or just about anything. I have made them for a Jensen marine radio and an SSV radio controller. Below are pictures of my pioneer and some other guys from facebook that have installed my panels. I work in a metal shop and cut these when we are slow. My price goes up significantly for small runs so I prefer to get several together and cut all at once to keep the costs down. I plan to place and order later this week (by 12-2-15) and will hopefully ship them out by next week. If you miss this order I can always cut more down the road. Let me know what you would like to see! Price is $25 shipped or $20 ea if you order 2 or more.
FB IMG 1441666594140 FB IMG 1445199676624 FB IMG 1446118746700 IMG 20150801 184955010 IMG 20150930 192559753
 
Last edited:
Hondasxs

Hondasxs

Club Founder
Staff member
Lifetime Member
Supporting Member
Feb 13, 2013
18,511
67,231
113
Charlotte, NC
HondaSxS.com
Ownership

  1. 1000-5

  2. Talon R
Kool. I like the options.
Was looking at the ram mount. But I may also need the Jensen radio in the future.
 
mystic1219

mystic1219

Active Member
Vendor
Lifetime Member
Jul 3, 2015
191
202
43
Kool. I like the options.
Was looking at the ram mount. But I may also need the Jensen radio in the future.
You could do both... I think 2 rows of 2 switches would fit in there also without being too crowded.
 
  • Like
Reactions: Nipper
Johnny_C

Johnny_C

Active Member
Nov 19, 2015
303
143
43
Western N. Carolina
I just ordered 10 switches from OTTR today.
I hope I can fit 2 rows of 5 in the upper
storage/cubby hole on my P1k. Anyone
have any input on if that will work?

Or, I guess I can put it the switch panel
where the decal is. How much would
that panel cost?

Thanks!

John
 
Last edited:
mystic1219

mystic1219

Active Member
Vendor
Lifetime Member
Jul 3, 2015
191
202
43
I don't have the measurements yet to make a panel for the far right opening but I charge $25 shipped for the warning label plates any way you want them ;)
 
  • Like
Reactions: CB111
Johnny_C

Johnny_C

Active Member
Nov 19, 2015
303
143
43
Western N. Carolina
How soon could I get a matching black
one from you? For the warning label
location. 2 rows of 5 for OTR switches,
centered.

Thanks!

John



I don't have the measurements yet to make a panel for the far right opening but I charge $25 shipped for the warning label plates any way you want them ;)
 
mystic1219

mystic1219

Active Member
Vendor
Lifetime Member
Jul 3, 2015
191
202
43
I should have enough orders for me to put in an order sometime this week. (If I order less than 10 my price nearly doubles so I try to wait until I have 10). We are a large laser shop and do work for snap-on, wal-mart, Harley-Davidson etc. If we get real busy it could take them up to a couple weeks to get to the plates. However we have been slow and I expect them to move pretty quick I just like to let people know it may take longer. I will add yours to my cut list. Thanks!
 
mystic1219

mystic1219

Active Member
Vendor
Lifetime Member
Jul 3, 2015
191
202
43
You can paypal $25 to [email protected] either now or when it's ready. If you'd rather mail a payment let me know.
 
  • Like
Reactions: JTW
advertisement
Tot

Tot

Well-Known Member
Lifetime Member
Dec 14, 2015
661
462
63
Des Arc, Arkansas
I'm liking the one on the bottom right with the 5 switches and the 4 screw holes.
I have started making custom laser cut and powder coated switch panels to replace the factory warning label on the dash for the 700 and 1000s. I use Carling Contura swtiches from OTRATTW.net but some others may fit. I have also made some to accept a 12v outlet, dual usb charging port or a volt meter. Another option is for a RAM mount to hold a cell phone, gps, go pro or just about anything. I have made them for a Jensen marine radio and an SSV radio controller. Below are pictures of my pioneer and some other guys from facebook that have installed my panels. I work in a metal shop and cut these when we are slow. My price goes up significantly for small runs so I prefer to get several together and cut all at once to keep the costs down. I plan to place and order later this week (by 12-2-15) and will hopefully ship them out by next week. If you miss this order I can always cut more down the road. Let me know what you would like to see! Price is $25 shipped or $20 ea if you order 2 or more.
View attachment 7977 View attachment 7978 View attachment 7979 View attachment 7980 View attachment 7981
 
mystic1219

mystic1219

Active Member
Vendor
Lifetime Member
Jul 3, 2015
191
202
43
Sending you a pm Tot
 
L

legend

New Member
Oct 27, 2015
9
5
3
I have started making custom laser cut and powder coated switch panels to replace the factory warning label on the dash for the 700 and 1000s. I use Carling Contura swtiches from OTRATTW.net but some others may fit. I have also made some to accept a 12v outlet, dual usb charging port or a volt meter. Another option is for a RAM mount to hold a cell phone, gps, go pro or just about anything. I have made them for a Jensen marine radio and an SSV radio controller. Below are pictures of my pioneer and some other guys from facebook that have installed my panels. I work in a metal shop and cut these when we are slow. My price goes up significantly for small runs so I prefer to get several together and cut all at once to keep the costs down. I plan to place and order later this week (by 12-2-15) and will hopefully ship them out by next week. If you miss this order I can always cut more down the road. Let me know what you would like to see! Price is $25 shipped or $20 ea if you order 2 or more.
View attachment 7977 View attachment 7978 View attachment 7979 View attachment 7980 View attachment 7981
I would like one for my 700-2 just a strit across 6 hole one do you have the switches also.
 
mystic1219

mystic1219

Active Member
Vendor
Lifetime Member
Jul 3, 2015
191
202
43
I would like one for my 700-2 just a strit across 6 hole one do you have the switches also.
I only make the panels. I use switches from otrattw.net they are top quality and very customizable. They run about $15 each. Amazon has some generic ones for about half that price that work fine.
 
  • Like
Reactions: Timb2-_
Tramguage1

Tramguage1

Texan
Moderator
Lifetime Member
Supporting Member
Club Contributor
Jul 2, 2015
7,500
30,748
113
Somereset, Texas
Ownership

  1. 1000-5

  2. 1000 6 Crew

  3. Talon X

  4. Talon R4 LV
Do you have any orders for another run? I would be interested in one. Also wonder if the 500 plate will fit the passenger side dash pocket in the 700.
 
mystic1219

mystic1219

Active Member
Vendor
Lifetime Member
Jul 3, 2015
191
202
43
I'm getting orders pretty quick for another run. I have several left, what are you looking for? The p500 panel does not fit the P700 pocket.
 
Tramguage1

Tramguage1

Texan
Moderator
Lifetime Member
Supporting Member
Club Contributor
Jul 2, 2015
7,500
30,748
113
Somereset, Texas
Ownership

  1. 1000-5

  2. 1000 6 Crew

  3. Talon X

  4. Talon R4 LV
I'm getting orders pretty quick for another run. I have several left, what are you looking for? The p500 panel does not fit the P700 pocket.
A couple of the 700 plates. What size is the small round hole? Is it entened for the round 12v plug or the round volt meter that's out there?
 
  • Like
Reactions: CB111
advertisement
Status
Not open for further replies.

About us

  • Our community has been around for many years and pride ourselves on offering unbiased, critical discussion among people of all different backgrounds. We are working every day to make sure our community is one of the best.

User Menu

Buy us a beer!

  • Lots of time and money has gone into making sure the community is running the best software, best designs, and all the other bells and whistles. Care to buy us a beer? We'd really appreciate it!

    Beer Fund!

    Club Membership!