Pioneer 1000 5 Rear Bumper

[Texas Jeffe]

I’m new to the club and I just got a Pioneer 1000 5 And would like to put a rear bumper on it. I have taken off the ROPS and would like to know if the rear mounting bolt connection points are the same as a 1000 3. I have seen some bumpers that qualify they will not fit the 5 but thought, maybe because of the ROPS and they don’t want the liability of saying it will fit if you remove the ROPS. Any advice is appreciated

 

[Admin]

 

[DaddyDubbs]

Welcome from Alabama. Sorry can't help you.

 

[Farmer]

Welcome from Northern ILL!!
Hopefully some 1000 owners will chime in soon to help. Have you checked the parts diagrams and lists at a place like Partzilla.com?

 

[Texas Jeffe]

No, I have not bit will call them today and see. Thanks

 

[Farmer]

🤔

 

[Rayger143]

I’m new to the club and I just got a Pioneer 1000 5 And would like to put a rear bumper on it. I have taken off the ROPS and would like to know if the rear mounting bolt connection points are the same as a 1000 3. I have seen some bumpers that qualify they will not fit the 5 but thought, maybe because of the ROPS and they don’t want the liability of saying it will fit if you remove the ROPS. Any advice is appreciated

I installed the Honda rear bumper. I could be wrong but I believe the 1000-3 and 1000-5 mount differently and I don't think it's got anything to do with the roll cage. I have a 1000-5 and it mounts at the tailgate hinges. If you have a 1000-5 buy a bumper for your model and it should mount with no problem roll cage or not.

 

[Texas Jeffe]

Thanks. That’s what I needed to know. I appreciate the help

 

[HBarlow]

A photo of your 1000-5 with ROPS removed might allow us to help you.

I recently bought and installed a Honda bumper for my 1000-3 from Rocky Mountain ATV. I think the bumper mounting point is by a bracket in the kit that attaches to the dump bed hinge. I don't KNOW but I THINK the oem Honda bracket will fit a1000-5 just like it does a 1000-3 with the ROPS removed.

 

[Texas Jeffe]

A photo of your 1000-5 with ROPS removed might allow us to help you.

I recently bought and installed a Honda bumper for my 1000-3 from Rocky Mountain ATV. I think the bumper mounting point is by a bracket in the kit that attaches to the dump bed hinge. I don't KNOW but I THINK the oem Honda bracket will fit a1000-5 just like it does a 1000-3 with the ROPS removed.

Thank you, I will check it out. On another note, I have got a bad rattle behind the seat. I was going to stuff it with some foam rubber but thought I would ask yall if you’ve had the same problem and what fixed it.

 

[HBarlow]

No, no mysterious rattles in mine. The engine, drivetrain, and tire noise is just short of unbearable in the cab but mine doesn't have any strange rattles.

 

[TripleB]

Thank you, I will check it out. On another note, I have got a bad rattle behind the seat. I was going to stuff it with some foam rubber but thought I would ask yall if you’ve had the same problem and what fixed it.

Look where the bed latches on both sides. Put some electrical tape on them for a quick fix. Tape won't last long I cant remember if there's any adjustment on the bed latches like you have on the door latches.

 

[Texas Jeffe]

Great idea. Thanks

 

[HBarlow]

If TripleB's suggestion is the cure, perhaps a strip of tape, rubber, or ??? on top of the frame where the dump bed rests would provide a spacer and tension the release arms enough to stop the rattle?