P1000 Honda Pioneer 1000 Internal gear reduction

[walexa07]

Gotcha. For resale purposes, surely there is a way around this? I wouldn't want to feel the need to disclose the fact that I had cut the frame under the floorboard in the past if I were to turn around and sell it down the line.

My understanding is there is a way around it - it's just alot more wrenching. Removing the cross member shaves lots of time off from what I have read.

Waylan

 

[Admin]

 

[Kilo427]

Comes with a bracket to reattach. That's what I will probably use vs welding that way if I ever need in that area again I can just unbolt it. The metal can't be supporting much it's fairly thin.

 

[Scooterchris]

Does the frame have to be cut for the install? That could be a deal breaker.

Your resale value goes way up when you put the internal gear reduction in.
Honda has a bad rap right now in the mudding and hardcore offroad ing seen for the clutches going out easy

 

[Scooterchris]

It's a simple rear floor board support
Take a hack saw or torch to it and either rebolt it with supplied bolts or weld it.
People are gonna want to know where you got it from once the see your buggy

 

[Scooterchris]

another successful install mark Powell of the 1000 Facebook group finished it up yesterday and loves it he's running on 30-inch Intimidators

 

[Scooterchris]

Mississippi monster.

Internal gear reduction + plus portals + 34.5's

This thing rips

 

[Ridem32]

Where is that at in Mississippi?


Sent from my iPhone using Tapatalk

 

[Manwell]

Just now looking at this thread, always impressed with the way people have the time, knowledge and wherewithal to make stuff like this! Hope it's a smashing success for @Scooterchris for all his effort!

 

[Scooterchris]

Where is that at in Mississippi?


Sent from my iPhone using Tapatalk

The owner of pearl river honda.

His name is Keith

 

[Ridem32]

He is not very far from me. I will call him and go check it out. Who did his IGR?


Sent from my iPhone using Tapatalk

 

[popeye]

Mississippi monster.

Internal gear reduction + plus portals + 34.5's

This thing rips

View attachment 28769

With the internal reduction plus the reduction of the portals and 34s, ratio wise where is the rig at compared to stock?

Sent from my LGMS631 using Tapatalk

 

[JTW]

With the internal reduction plus the reduction of the portals and 34s, ratio wise where is the rig at compared to stock?

Sent from my LGMS631 using Tapatalk

6

 

[popeye]

6

6 what? % above or below stock?

Sent from my LGMS631 using Tapatalk

 

[Ridem32]

It's about 50%


Sent from my iPhone using Tapatalk

 

[JTW]

6 what? % above or below stock?

Sent from my LGMS631 using Tapatalk

Nope.. just 6

 

[Scooterchris]

He is not very far from me. I will call him and go check it out. Who did his IGR?


Sent from my iPhone using Tapatalk

He did the reduction himself.
They will do it at pearl river honda

 

[Scooterchris]

With the internal reduction plus the reduction of the portals and 34s, ratio wise where is the rig at compared to stock?

Sent from my LGMS631 using Tapatalk

Stacking the portals on top of the igr makes the total reduction 59 percent.

45 mph was top speed gps verified on 34.5's

 

[Scooterchris]

It's a monster



With my 30 inch outbacks and just the IGR. I'll blow a stock buggy out of the water

 

[popeye]

Stacking the portals on top of the igr makes the total reduction 59 percent.

45 mph was top speed gps verified on 34.5's

Thats about perfect imo. Bet that makes some serious tork now

Sent from my LGMS631 using Tapatalk

 

[Scooterchris]

Thats about perfect imo. Bet that makes some serious tork now

Sent from my LGMS631 using Tapatalk

Yes sir