Russ989’s Trifecta Build

[Russ989]

Hey Russ you ever get a chance to measure your width in the front?

I will try to do that tomorrow.

 

[Admin]

 

[Patron1960]

I like your thinking JB. I might have to incorporate those ideas!

Lol that’s awesome!! I’ve had two rangers and both were ok but I don’t work mine that hard! The 1990 Honda Rancher four wheeler I bought in 90’ is still a work horse although it is a bit ugly now! Like me! I currently have a 2020 Honda 1000-5 limited! Great machine! One problem was a CV joint was bad after 200 miles so dealer replaced no issues! Thanks guys I enjoy the reading! I’m in Willis Texas!

 

[Patron1960]

I also added the 12” add a light bar kit from the store as well. It works on your dimmer switch when you turn on your high beams.

Where can I get these lights with plug n play harness?

 

[Todd627]

Where can I get these lights with plug n play harness?

Here is the link to the light form the HondaSxS Store.

add-a-light-high-beam-led-light-bar-for-honda-pioneer-1000

 

[Russ989]

Finally got around to installing the harness bar from Brick City Fab and the Dragonfire Evo harnesses.

 

[Ridinfool]

Finally got around to installing the harness bar from Brick City Fab and the Dragonfire Evo harnesses.

View attachment 274442 View attachment 274443

Nice setup, I’d like to check out those harnesses at the TO.

 

[Russ989]

Nice setup, I’d like to check out those harnesses at the TO.

Absolutely

 

[Tigermark]

Finally got around to installing the harness bar from Brick City Fab and the Dragonfire Evo harnesses.

View attachment 274442 View attachment 274443

Bout time. Looks good

 

[ToddACimer]

Finally got around to installing the harness bar from Brick City Fab and the Dragonfire Evo harnesses.

View attachment 274442 View attachment 274443

You're going to like the Evos. Great harness for trail riding. Just dont ride in a machine with Can-am 4 point retractable harnesses

 

[BlownCJ]

Russ looks like you are still running factory axles. Is this why you only used 3/4 inch spacers? I keep a dial caliper in my office and ordered some 30 dollar spacers from PBR and the fronts are 1.125 in and rear spacers are 1.375 in. I was thinking of stopping over at a buddys house and parting them to .875 ( 7/8 ths) and calling it good . Curious about this .

 

[JenElio]

Russ looks like you are still running factory axles. Is this why you only used 3/4 inch spacers? I keep a dial caliper in my office and ordered some 30 dollar spacers from PBR and the fronts are 1.125 in and rear spacers are 1.375 in. I was thinking of stopping over at a buddys house and parting them to .875 ( 7/8 ths) and calling it good . Curious about this .

Wheel spacers?

 

[BlownCJ]

Shock spacers for lift so 30s do not scrub

 

[JenElio]

Shock spacers for lift so 30s do not scrub

Ohhh..... Most 30s will rub unless you get off set a-arms.

 

[Isaiah]

Shock spacers for lift so 30s do not scrub

You will need offset A arms to clear 30s and some 30s will need A arms and a lift to clear depends on how true to size they are

 

[BlownCJ]

I have offset arms .

 

[Russ989]

Evening gang, I’ve been so busy I haven’t posted any updates in quite awhile. Here the install video for the upper soft doors.


Honda Pioneer 1000 Soft Upper Doors

 

[Russ989]

Here’s an install video for the WFO adjuster that works with the SATV windshield.


WFO SXS Adjuster

 

[Russ989]

Install for the fan override kit.


Honda Pioneer 1000 Fan Override

 

[BWAF]

Nice job on videos I would never attempt one on doors more than you think but not a bad job , I'm 2 years in on upper doors still no problems

 

[Russ989]

Nice job on videos I would never attempt one on doors more than you think but not a bad job , I'm 2 years in on upper doors still no problems

They are pretty good for what they are for sure. Mine have had a lot of brush drag across them and are still in great shape.