P500 What did you do to/with your Pioneer 500 today?

[rustyneversleeps]

Slanged some mud

 

[Admin]

 

[trigger]

Rode with an RMax today. Bounced it off the limiter a few times to say the least. Old Ironsides didn't out do it in any aspect but followed it everywhere and did it all damn day.

 

[Weberman]

The P5 held her own this week MT elk hunting! The only side x side in the group. My buds were very impressed how it performed on the 50” trails with their Ranchers and Foremans! They all wanted to ride it all week .

 

[Bmurray]

Excellent machine, congrats on the elk

 

[jmaxch]

Went grouse hunting with the P500. It’s nice to know that’s your in a reliable machine in the middle of nowhere.

 

[wvupsc]

I ran my P520 this morning while doing some chores. It was the coldest day that I have run it so far: ~40 degrees. When I started to shift it through the gears, I thought it wasn't shifting. I had to look at the dash board display to make sure it was...and in fact it was. It has never shifted so smoothly. I am assuming it has something to do with the cooler temps. But the hard shifting was gone. It was smooth as silk and practically unnoticeable. I have a whopping 65 miles on my 520, and I bought it in April.

 

[Dave75]

Today I moved my dad’s hunting blind into the woods. Two years ago a Suzuki 400 King Quad could just move it. Last year a Yamaha 600 Grizzly move it with no problems. This year the p520 move the blind just as good as the Grizzly. I was surprised the p520 did as good as the Yamaha with the p520 engine being about 80cc less.

 

[Red500]

Got second battery install finished today (well: until I decide to change something).

Installed fuse box and tried to neaten up under the hood.

 

[Buzzbomber]

Finally put the Pioneer to work hauling firewood I cut months ago from a tree that got struck by lightning this summer out of the woods. Did about 10 loads like this. Too bad it sat on the ground so long…

 

[Mudder]

Did an oil change and still amazed how small the P500 oil filter is compared to my Rancher 420. Access hole mod made the job quicker.

 

[PJ1]

Hooked up the plow today. Noticed the push tubes full of rust inside, so I slathered 'em with Amsoil metal protector.

 

[wvupsc]

Installed my Elka Stage 3's!

 

[Montecresto]

The P5 held her own this week MT elk hunting! The only side x side in the group. My buds were very impressed how it performed on the 50” trails with their Ranchers and Foremans! They all wanted to ride it all week . View attachment 302565View attachment 302566View attachment 302567

Nice camp too….👍😎

 

[Mudder]

Got second battery install finished today (well: until I decide to change something).
View attachment 303425
Installed fuse box and tried to neaten up under the hood.
View attachment 303426

Nice job. Need to organize mine wiring since the original 2016 effort. Lots of excellent examples shown since that time.

 

[Red500]

Nice job. Need to organize mine wiring since the original 2016 effort. Lots of excellent examples shown since that time.

I may have to move my breakers to somewhere else. When we got back from the PC ride they where covered in mud, and though I've sprayed them off a couple of times, they still have sand in them and don't want to work properly. I've had a heck of a time getting all the sand from there rinsed out of everything.

 

[Mudder]

I may have to move my breakers to somewhere else. When we got back from the PC ride they where covered in mud, and though I've sprayed them off a couple of times, they still have sand in them and don't want to work properly. I've had a heck of a time getting all the sand from there rinsed out of everything.

Clear Saran wrap over them??

 

[Red500]

Clear Saran wrap over them??

Been thinking of ways to cover them. I still want them to be as accessible as possible though. Maybe some kind of hinged box type thing?

 

[Todd627]

Been thinking of ways to cover them. I still want them to be as accessible as possible though. Maybe some kind of hinged box type thing?

This is where I put mine. It stayed clean there.

 

[Red500]

This is where I put mine. It stayed clean there.

View attachment 305408

So far I haven't had any problems with the fuse box. It's the breakers that I mounted by the second battery (under driver's seat) that I'm going to have to do something about. I kinda figured I might have a problem when I mounted them where I did.

 

[Todd627]

So far I haven't had any problems with the fuse box. It's the breakers that I mounted by the second battery (under driver's seat) that I'm going to have to do something about. I kinda figured I might have a problem when I mounted them where I did.

10-4. I misunderstood what you were saying 👍🏼