P500 Bigtee’s P520 Build

[The Green Goat]

I’m hoping this will leave me room for power steering later on, I kept over toward the passenger side as far as I could.

Man, you move quick with the mods!

You'll be fine with power steering with your battery where it is.

 

[Admin]

 

[Bigtee]

Man, you move quick with the mods!

You'll be fine with power steering with your battery where it is.

I’m retired and like to stay busy. I mess around with something every day. I also have 62 acres which I mow about 18 acres of it.

 

[Bigtee]

I got a little bit of electrical work done today. Isolator installed, aux battery is hooked up and both bus bars hooked up. I got My switch panel installed but none of the wiring is hooked up. I will clean it up some once all the wiring is completed.

 

[Bigtee]

I also finally got around to eliminating the reverse lever.

 

[1border4manu]

I also finally got around to eliminating the reverse lever.

The best mod out of all of them.

 

[Gb3]

How do you eliminate the reverse lever?

 

[trigger]

Just adjust the cable on the backside of the lever under the hood.

 

[Bigtee]

How do you eliminate the reverse lever?

 

[wvupsc]

It was so easy even I could do it.

 

[rustyneversleeps]

@Bigtee Did you ever get the seatbelt delete to work? Were you using this one?

Harness accessory seat belt override bypass - Pioneer 500/520

Used when installing an aftermarket safety harness. This unit bypasses the standard seatbelt limiter instated by the manufacturer. Simple plug-and-play leave the OEM system intact allowing easy reversal if the safety harnesses are ever removed. Plug n Play for Easy Install. Dummy plug to...

store.hondasxs.com

 

[Bigtee]

@Bigtee Did you ever get the seatbelt delete to work? Were you using this one?

Harness accessory seat belt override bypass - Pioneer 500/520

Used when installing an aftermarket safety harness. This unit bypasses the standard seatbelt limiter instated by the manufacturer. Simple plug-and-play leave the OEM system intact allowing easy reversal if the safety harnesses are ever removed. Plug n Play for Easy Install. Dummy plug to...

store.hondasxs.com

I have the correct one now, the one that I had was for a P1000 or P700. Next time I have the seat out I will install it. I'm sure it will work correct now. For now I have one of these,

 

[Bigtee]

Wiring is complete except for remote for winch. When I get it installed I’ll clean everything up.

 

[Bigtee]

I also added the all-thread mod to the light bar.

 

[Bmurray]

this has to be one of the best looking Pioneers that I've seen.

 

[Montecresto]

this has to be one of the best looking Pioneers that I've seen.

It’s pretty. You should see what @Stacy built.

 

[The Green Goat]

I also added the all-thread mod to the light bar.

View attachment 272362

What's the point of the all-thread mod? What all is involved?

 

[Bigtee]

What's the point of the all-thread mod? What all is involved?

It’s just all-thread to help stabilize the end brackets. The Allen head bolts that hold the light to the bracket can vibrate loose. I put a piece of vacuum line over it to hide the all-thread.

 

[Bigtee]

Also, if you are mounting a SuperWinch on the new StrongMade winch bumper, you’ll need longer bolts than what are supplied with the winch. Here’s what it took.

 

[trigger]

It’s just all-thread to help stabilize the end brackets. The Allen head bolts that hold the light to the bracket can vibrate loose. I put a piece of vacuum line over it to hide the all-thread.

Someone's been doing his research.

 

[Bigtee]

Also, if you are mounting a SuperWinch on the new StrongMade winch bumper, you’ll need longer bolts than what are supplied with the winch. Here’s what it took.

View attachment 272507

Correction, these are not long enough either. I have some 35MM and 40MM lenghts coming tomorrow. Maybe I will get the winch lined out finally.