P1000 My 1000-5 After one year

[aauman88]

2.5” front and 1.25 in rear. Run front on soft 1 and rear on middle 2 unless fully loaded and then hard 3 on rear

 

[Admin]

 

[THEOLDMAN]

2.5” front and 1.25 in rear. Run front on soft 1 and rear on middle 2 unless fully loaded and then hard 3 on rear

What is the toe in spec

 

[aauman88]

What is the toe in spec

I’ve got mine as close to neutral as I can get it with touch of toe out. Seems to help it track better on soft stuff with low air pressure in the tires.

 

[aauman88]

Current shop situation. Got a little mess

 

[aauman88]

SATV windshield in and all wires rerouted off front cage. Now just to finish snorkel, install the 52” light bar and put my buddies Pioneer back together

 

[aauman88]

New 54” straight bar and PBR brackets in. Want shorter light brackets so it’s closer to windshield but I’m happy with setup

 

[aauman88]

Working on new snorkel. Ordered the 3” Amazon pipe and used 4” piece of stock air intake from my buddies. It fit extremely tight inside factory pipe, is thin walled and the 3” hose fit perfectly over it. Added the flexible boot and hose clamps just in case. Ran through hole in fender my old snorkel went through and pipe is up high in dash beside cupholder. Should I put FrogSkinz material over end just in case? I will never purposely put my machine in water over dash but we do play deep

 

[aauman88]

Actually decided to move it to the highest part of dash above glove box. There’s no openings above it for water to get but I still may put the FrogSkinz material over it

 

[aauman88]

Under hood packed and ready for this weekend at lake

 

[aauman88]

Another great weekend at lake. The new windshield, roof vents and windshield extender gave unlimited options that did away with all dust in cab and kept everyone comfortable in 100* GA heat

 

[aauman88]

Power Commander 5 ordered. $287 after 10% back so figured worth a shot. Probably be adding the HMF exhaust next

 

[aauman88]

Well HMF Titan QS black out exhaust ordered. 450$ after 10% back. Excited for these two additions

 

[CumminsPusher]

Well HMF Titan QS black out exhaust ordered. 450$ after 10% back. Excited for these two additions

That exhaust note is badass!

 

[aauman88]

Hope it’s not too loud, don’t want to hear my wife fuss about it

Now to find a good map for the PC5

 

[aauman88]

 

[aauman88]

Exhaust is in. Broke both bolts off in the old flange so have standard bolts in the new one without the springs until new bolts come in. Exhaust sounds good but only ran a second before got back inside with family. Do you put the stock heat shield back on the HMF or not?? Bolts I had wouldn’t work with springs on flange so left them off, that will be fine temporary right?

 

[jwfirebird]

they put those on so you dont melt the plastic in hot areas going slow, so i would definitely replace the heat shield. looks pretty cool

 

[aauman88]

The heat shield bolts to factory exhaust and at first glance didn’t see a way to attach to new exhaust but I will pull it apart and check it next time in the shop

 

[CumminsPusher]

I wouldn’t put those back on even if you could. I haven’t heard of any problems and none in ours. It runs cooler anyways.

 

[aauman88]

I wouldn’t put those back on even if you could. I haven’t heard of any problems and none in ours. It runs cooler anyways.

Cool thanks