P1000 Todd's 2018 Build

[ToddACimer]

A little confused on the pipe lengths,The horizontal piece looks longer than 3". Would 3' exhaust tubing work for both straight pieces?

3ft would be more than enough. The horizontal piece is 12.5" and the vertical on mine is 3".

 

[Admin]

 

[Tramguage1]

Thanks, just ordered the 90's and snorkel head. i will pickup some tubing next week. I have been wanting to snorkel but not through the hood. It looks great!

 

[ohanacreek]

Thanks, just ordered the 90's and snorkel head. i will pickup some tubing next week. I have been wanting to snorkel but not through the hood. It looks great!

PM me your address I have a section laying around somewhere I’ll send you.

Edit: NM I gave it away at takeover.

 

[ToddACimer]

Thanks, just ordered the 90's and snorkel head. i will pickup some tubing next week. I have been wanting to snorkel but not through the hood. It looks great!

Order these too. They make great prefilters
2 X UNIFILTER Safari Snorkel Ram Head (150Wx100H) Cover Pre Cleaner Filter | eBay

 

[Plumber32]

Order these too. They make great prefilters
2 X UNIFILTER Safari Snorkel Ram Head (150Wx100H) Cover Pre Cleaner Filter | eBay

How long did it take to receive?

 

[ToddACimer]

How long did it take to receive?

2 weeks

 

[Tramguage1]

How long did it take to receive?

@Plumber32 Think we can get them before Colorado?

 

[ToddACimer]

I have 2 and no plans to ride for 3 weeks if shipping looks close.

 

[Plumber32]

@Plumber32 Think we can get them before Colorado?

I put on a regular k&n for the dusty times.

 

[ToddACimer]

Well on Tuesday I was thinking if look over the bent a-arms and see how the new SuperATV arms looks. Today I unboxed the SuperATV arms and I'm certain upper a-arm gussets are needed.

I pressed a new set of Honda Ball joints in the SuperATV arms this after noon. Overall impressed, these arms are huge compared to stock. The Honda arms in these photos are my straight spares not the mangled 2018 arms with 500 miles of light trail usage

 

[ToddACimer]

Back to work on this thing. A-arm mounts gusseted and SuperATV arms going on. Fixed a ripped inner front CV boot too. I'll swap to stainless brake lines before it comes off the lift too.


Upper tab

Lower tab

Why'd I do the lower front??? Well this looks kinda bad. My assumption is the compliance of the Honda a-arm bushing saved me a but more damage here. With the SuperATV arms and bushings I might not be so lucky.

 

[BWAF]

Back to work on this thing. A-arm mounts gusseted and SuperATV arms going on. Fixed a ripped inner front CV boot too. I'll swap to stainless brake lines before it comes off the lift too.


Upper tab
View attachment 148748 View attachment 148749 View attachment 148750


Lower tab
View attachment 148751
View attachment 148752

View attachment 148753

Why'd I do the lower front??? Well this looks kinda bad. My assumption is the compliance of the Honda a-arm bushing saved me a but more damage here. With the SuperATV arms and bushings I might not be so lucky.

View attachment 148754

I like it

Sent from my SM-G930U using Tapatalk

 

[ToddACimer]

I felt really good about finishing this around 7pm. Can't find my steering stops anywhere and only got one all together for today.

 

[SXS12345]

Installed the Superwinch Terra45 on a Warn mount. The warn mount fit was less than great but I made it fit. Not sure about the winch being upside down but the cable routing is nice. I installed the 12" RC light bar on the bumper and recovery points installed.

View attachment 131756 View attachment 131757

where did you get the mounting clamps for the light bar? sweet rig!!

 

[ToddACimer]

where did you get the mounting clamps for the light bar? sweet rig!!

LAMPHUS 2PC Off-Road LED Light Bar 0.75"/1"/1.25" Vertical Bar Clamp Mounting Kit [Rubber Teeth] [Aluminum] [Includes Hex Key] [for Bull Bars, Roof Racks, Roll Cages] for ATVs, UTVs, and Trucks https://www.amazon.com/dp/B07FT2KVNL/?tag=sxsweb24-20

 

[SXS12345]

LAMPHUS 2PC Off-Road LED Light Bar 0.75"/1"/1.25" Vertical Bar Clamp Mounting Kit [Rubber Teeth] [Aluminum] [Includes Hex Key] [for Bull Bars, Roof Racks, Roll Cages] for ATVs, UTVs, and Trucks https://www.amazon.com/dp/B07FT2KVNL/?tag=sxsweb24-20

i appreciate it!

 

[ToddACimer]

I welded up the right side today. Overall really happy with the fit of the mount gussets and SuperATV arms. The camber was perfect out of the box and the alignment was pretty easy.

Right side welded up and painted with Rust-Oleum 2x paint/primer in gloss black

Back on the ground

Hill Billy alignment, 1/8" toe in and a straight wheel sounds good to me.

Next up:

300lb springs for the rear fox shocks
Left rear outer CV boot.
Grease rear wheel bearings.

The new machine has 455 miles of fun on it.

 

[CumminsPusher]

I welded up the right side today. Overall really happy with the fit of the mount gussets and SuperATV arms. The camber was perfect out of the box and the alignment was pretty easy.

Right side welded up and painted with Rust-Oleum 2x paint/primer in gloss black
View attachment 149402

Back on the ground

View attachment 149403
View attachment 149404

Hill Billy alignment, 1/8" toe in and a straight wheel sounds good to me.
View attachment 149405


Next up:

300lb springs for the rear fox shocks
Left rear outer CV boot.
Grease rear wheel bearings.

The new machine has 455 miles of fun on it.

Hey that HillBilly alignment is the best out there. Looking good man! Nice job

 

[Neohio]

I had some weld washers turned for the upper control arm if you want me to send you a set to trial.
CP installed some last weekend on his ride.

 

[ToddACimer]

I had some weld washers turned for the upper control arm if you want me to send you a set to trial.
CP installed some last weekend on his ride.

Would have been a lot easier to install them on my weld on tabs before burning them onto the machine. I looked into doing the washers but for now I think this will work