P500 What did you do to/with your Pioneer 500 today?

[Deleted member 3748]

I didn't measure what the new wheels/tires are. Before it was stock.

I still squeezed through the tight 50" trails with those tires.

 

[Deleted member 3748]

Can you get me a full skid plate. It’s looking like I’ll have to get it from somewhere down there and hope they ship to Canada. So much for free trade. Haha.
Caper

I'm all out of things to sell... sorry.

 

[Caper]

I didn't measure what the new wheels/tires are. Before it was stock.

I’ve still got the stock rims because some trails have a pole in the centre to keep it just over 50”. I like the black.
Caper

 

[Caper]

I'm all out of things to sell... sorry.

Haha. All good.
Caper

 

[Caper]

I still squeezed through the tight 50" trails with those tires.

Nice
Caper

 

[Caper]

Oak Island should be good tonight. What’s next. Haha
Caper

 

[Deleted member 3748]

Oak Island should be good tonight. What’s next. Haha
Caper

Have they found anything yet?

 

[GRANITE]

@PistonHonda what did you put on your x2?

 

[Deleted member 3748]

@PistonHonda what did you put on your x2?

Bighorn 2.0s. I wanted a light tire to maintain performance.

 

[GRANITE]

What size? 12” rims?

 

[Deleted member 3748]

What size? 12” rims?

27x9-12 in the front and 27x11-12 in the rear. I kept the Yamaha aluminum wheels.

 

[Caper]

Have they found anything yet?

Last week your boys from Michigan did the dye test again and found it in the cove where they excavated. They also find a hinge from the 1600’s. They are spending money. Which is good for here. Haha
Caper

 

[Mudder]

Put new shoes on. Thanks to @PistonHonda for the good deal

View attachment 115496View attachment 115497

Bet he threw in the high performance air along with the tires. Looks sharp!

 

[DG Rider]

Just ordered the cheap Amazon front pads. Finally hit the sensors...

 

[AlR]

[HASHTAG]#OilChangePorn[/HASHTAG]

View attachment 112716

That oil works in the wet clutch?

 

[ALM76]

Been a project for a few weeks..... I wanted a bumper a little different from the ones already out there. I thought the lines of the Pioneer looked pretty mean on the front and wanted a bumper to keep that look. Sent my cardboard model to a buddy, with all the cool metal working toys, and he came back with this! I used 11 gauge for the mount and 14 gauge for the bumper to be stout enough for the winch. Used Rust-Oleum Truck Bed Coating for the finish. Turned out Bada$$!

 

[Todd627]

Been a project for a few weeks..... I wanted a bumper a little different from the ones already out there. I thought the lines of the Pioneer looked pretty mean on the front and wanted a bumper to keep that look. Sent my cardboard model to a buddy, with all the cool metal working toys, and he came back with this! I used 11 gauge for the mount and 14 gauge for the bumper to be stout enough for the winch. Used Rust-Oleum Truck Bed Coating for the finish. Turned out Bada$$!

View attachment 115651 View attachment 115653 View attachment 115654

@ALM76 that turned out tits!! Cost for me to get one?

 

[mudallovertheplaces]

Submerged P500 problems? 12 screws to open up the gauge and drain it. Let it dry out then reassemble. I need silicone the back boot. Hopefully that will prevent further water intrusion. Also had an issue the other day. I started the bike and it just died. Check main 30a fuse and sure enough it had some corrision. Changed it out and all good now.

 

[Montecresto]

Been a project for a few weeks..... I wanted a bumper a little different from the ones already out there. I thought the lines of the Pioneer looked pretty mean on the front and wanted a bumper to keep that look. Sent my cardboard model to a buddy, with all the cool metal working toys, and he came back with this! I used 11 gauge for the mount and 14 gauge for the bumper to be stout enough for the winch. Used Rust-Oleum Truck Bed Coating for the finish. Turned out Bada$$!

View attachment 115651 View attachment 115653 View attachment 115654

Great job!!!!

 

[Caper]

Been a project for a few weeks..... I wanted a bumper a little different from the ones already out there. I thought the lines of the Pioneer looked pretty mean on the front and wanted a bumper to keep that look. Sent my cardboard model to a buddy, with all the cool metal working toys, and he came back with this! I used 11 gauge for the mount and 14 gauge for the bumper to be stout enough for the winch. Used Rust-Oleum Truck Bed Coating for the finish. Turned out Bada$$!

View attachment 115651 View attachment 115653 View attachment 115654

Great job.
Caper