P1000 wheels offset

[Yotebuster]

New here did some reading cannot find answer to my question exactly I’m wanting to buy some aftermarket rims for my pioneer 1000 -3. SE edition. I want to run the same size tire front and rear which will be a 28 x 10 x 14 so if I bought a 14 x 7 wheel with a 5+2 offset do I have to buy wheel spacers for the rear to make the front and rear tires track the same I do not care about making my stance wider I just want the tires to track exactly the same and be able to rotate front to rear thanks for the info

 

[Admin]

 

[Mopower58]

Welcome from Mississippi. I have a 2016 P1K-3 and I just added a 1 inch spacer on the rear to even it up. I have 28x9's up front and 28x11's in the rear, both on 5+2 wheels.
#NTC

 

[Hillbillytnt]

New here did some reading cannot find answer to my question exactly I’m wanting to buy some aftermarket rims for my pioneer 1000 -3. SE edition. I want to run the same size tire front and rear which will be a 28 x 10 x 14 so if I bought a 14 x 7 wheel with a 5+2 offset do I have to buy wheel spacers for the rear to make the front and rear tires track the same I do not care about making my stance wider I just want the tires to track exactly the same and be able to rotate front to rear thanks for the info

Exactly is hard to get. Your fronts are 6.5 wide and rear are 8. Your wanting to go to a 7. I think you want as close as you can get.

 

[Yotebuster]

Exactly is hard to get. Your fronts are 6.5 wide and rear are 8. Your wanting to go to a 7. I think you want as close as you can get.

true. so a 1 or 1 1/2” wheel spacer on rear should get me darn close in think to the front with same wheels all way around?

 

[Worse1]

true. so a 1 or 1 1/2” wheel spacer on rear should get me darn close in think to the front with same wheels all way around?

1” should do you right.

 

[PJon]

I have 14x7 5-2 all the way around with 28x10x14 tires. 1” spacers on the rear pretty much evens it out. If you use the spacers I’d recommend getting them from RB3 Offroad. They’re a little over 1” so you won’t have to grind off the studs and nuts to get a flush mount on the wheels.

 

[Dusty 82]

Welcome from Mississippi. I have a 2016 P1K-3 and I just added a 1 inch spacer on the rear to even it up. I have 28x9's up front and 28x11's in the rear, both on 5+2 wheels.
#NTC

Thinking about going with a setup similar to this how much wider did this make your front end? I would like to run skinny wide but with 5+2 front and 4+3 rear and no spacers.

 

[PJon]

If you run 5-2 on all 4 corners with 1” wheel spacers on the rear, you’ll be able to rotate your tires. If you run 4-3 on the rear with no spacers, you’ll be about 1-1/2” narrower in the rear.

 

[Dusty 82]

If you run 5-2 on all 4 corners with 1” wheel spacers on the rear, you’ll be able to rotate your tires. If you run 4-3 on the rear with no spacers, you’ll be about 1-1/2” narrower in the rear.

Gotcha,thanks I’m just gonna go with 5-2 on all four.

 

[Remington]

Thinking about going with a setup similar to this how much wider did this make your front end? I would like to run skinny wide but with 5+2 front and 4+3 rear and no spacers.

Gotcha,thanks I’m just gonna go with 5-2 on all four.

Welcome from the Putrid Swamp Run Michigan!

What rig do u have that your putting these on?

 

[Dirtstiffs-1000]

5+2 offset - Tusk wheels
28x10x14 - Tusk tires
Initially installed 1" rear spacer but removed.
Counteract balance beads
Very happy with this combination

 

[Dusty 82]

Welcome from the Putrid Swamp Run Michigan!

What rig do u have that your putting these on?

2021 p1000-5 deluxe

 

[PJon]

If you run 5-2 on all 4 corners with 1” wheel spacers on the rear, you’ll be able to rotate your tires. If you run 4-3 on the rear with no spacers, you’ll be about 1-1/2” narrower in the rear.

Sorry, I goofed up my calculations on that. You’d actually be about 1/2” wider in the rear.

 

[Sjc3081]

I dont want my P1000 any wider. STI HD9 6+1 front and 5+2 rear. Keep factory width of 63”. Being able to rotate the tires is not worth the expense of spacers or excess bearing and suspension wear due to wider offset.

 

[Remington]

2021 p1000-5 deluxe

Pics Or It Didnt Happen!

 

[Dusty 82]

Pics Or It Didnt Happen!

 

[Dusty 82]

 

[Dusty 82]

View attachment 369431

I’ve done basic upgrades so far just trying decide on wheels and tires.Thinking about trying 28x9/11 terrahooks on factory wheels

 

[Remington]

View attachment 369431

I’ve done basic upgrades so far just trying decide on wheels and tires.Thinking about trying 28x9/11 terrahooks on factory wheels

Looks good man! Always liked the white. Thanks for posting.
If your all stock, and I know this isnt flashy as wheels. The first thing u should be doing is get rid of the factory “G” string skid plate and get yourself a full aftermarket skid. Also a snorkel kit. @Bayouownbeer sells a nice inexpensive kit. Trust me, if u think u need it or not, youll be glad u did! Would be a shame to have those nice wheels and messed up machine so u cant show them off! Use the search up top for skid plate options. Start a build thread with your progress as well.

 

[Bayouownbeer]

Looks good man! Always liked the white. Thanks for posting.
If your all stock, and I know this isnt flashy as wheels. The first thing u should be doing is get rid of the factory “G” string skid plate and get yourself a full aftermarket skid. Also a snorkel kit. @Bayouownbeer sells a nice inexpensive kit. Trust me, if u think u need it or not, youll be glad u did! Would be a shame to have those nice wheels and messed up machine so u cant show them off! Use the search up top for skid plate options. Start a build thread with your progress as well.

Thanks for recommending. Anyone interested send me PM.