JayPo's 2024 Talon 1000R

[JayPo]

Did ya get a Packout cooler?

Not yet

 

[Admin]

 

[Scoop]

Not yet

I see a perfect spot for one.

 

[JayPo]

I have my tablet mounted up on the ROPS above the windshield. It is powered via a USB cable so I want to add a USB port up there somewhere. Anyone have any ideas on a good way to do this? All the USB ports I find are either rocker switch size or the ones designed to go into a round hole in the dash.

 

[Coeus]

I have my tablet mounted up on the ROPS above the windshield. It is powered via a USB cable so I want to add a USB port up there somewhere. Anyone have any ideas on a good way to do this? All the USB ports I find are either rocker switch size or the ones designed to go into a round hole in the dash.

For my rear view mirror I hard wired a long usb cable to an auxbeam input

Major General 2024 Talon 1000R-4 Build Thread

Power converter from 12v to 5v ordered with arrival on Thursday Just curious 🤔 why not wire it directly to the key-on 12V busbar or similar?

hondasxs.com

 

[JayPo]

For my rear view mirror I hard wired a long usb cable to an auxbeam input

Major General 2024 Talon 1000R-4 Build Thread

Power converter from 12v to 5v ordered with arrival on Thursday Just curious 🤔 why not wire it directly to the key-on 12V busbar or similar?

hondasxs.com

I'm more looking for mounting ideas for a USB port. I don't want a long USB cable routed from under the hood to the tablet because USB cables always go bad. I'll route the accessory 12V into some type of USB port (like this or this or this or something else?). I just can't figure a good way to mount any of these up there.

 

[Scoop]

I have my tablet mounted up on the ROPS above the windshield. It is powered via a USB cable so I want to add a USB port up there somewhere. Anyone have any ideas on a good way to do this? All the USB ports I find are either rocker switch size or the ones designed to go into a round hole in the dash.

I did this in my P1K5:

P1000 - Scoop's 2021 P1K5 Deluxe Phantom Camo Build

Spent a couple hours swapping the OEM springs on some new Fox QS3 fronts (3P) and rears (5P) with Viper linear rate springs (F: 250#/R: 300#). Would like to find time tomorrow to get them swapped out on the bike, but it's a busy weekend.

hondasxs.com

I bought one of these for the housing and wiring only:

Attwood 11862-6 Universal 12V Cigarette Lighter Adapter Socket Outlet for Marine/RV with Mounting Kit, Black

... then swapped the 12V socket for one of those round USB charger sockets (the blades on the back are the same), then I mounted the housing directly to the back of RAM tablet holder.

 

[JayPo]

I did this in my P1K5:

P1000 - Scoop's 2021 P1K5 Deluxe Phantom Camo Build

Spent a couple hours swapping the OEM springs on some new Fox QS3 fronts (3P) and rears (5P) with Viper linear rate springs (F: 250#/R: 300#). Would like to find time tomorrow to get them swapped out on the bike, but it's a busy weekend.

hondasxs.com

I bought one of these for the housing and wiring only:

Attwood 11862-6 Universal 12V Cigarette Lighter Adapter Socket Outlet for Marine/RV with Mounting Kit, Black

... then swapped the 12V socket for one of those round USB charger sockets (the blades on the back are the same), then I mounted the housing directly to the back of RAM tablet holder.

I have a different Ram tablet mount that doesn't have a nice place to mount the housing like yours, but I might can rig something up similar. Thanks.

 

[JayPo]

Fixed yet another rattle on the JAH. The drivers door rattled because it did not close tightly. I adjusted the door latch inside the door but there is not enough adjustment allowed to make the door close tight so it still rattles. So I put one of those round felt pads that goes on furniture feet on the door where it meets the rubber stopper on the unit. Door is now quiet.

Update: see this post for the more better fix to the door rattle

 

[Coeus]

Fixed yet another rattle on the JAH. The drivers door rattled because it did not close tightly. I adjusted the door latch inside the door but there is not enough adjustment allowed to make the door close tight so it still rattles. So I put one of those round felt pads that goes on furniture feet on the door where it meets the rubber stopper on the unit. Door is now quiet.

POIDH

 

[EMAW]

Fixed yet another rattle on the JAH. The drivers door rattled because it did not close tightly. I adjusted the door latch inside the door but there is not enough adjustment allowed to make the door close tight so it still rattles. So I put one of those round felt pads that goes on furniture feet on the door where it meets the rubber stopper on the unit. Door is now quiet.

There is a rubber bumper that you can adjust (turn in/out).

 

[JayPo]

There is a rubber bumper that you can adjust (turn in/out).

Thanks EMAW. I didn't realize that bumper was adjustable. I moved it out a little bit and no more door rattle 👍

POIDH

 

[Coeus]

There is a rubber bumper that you can adjust (turn in/out).

I might have to do this mod too

 

[JayPo]

Installed Hillbilly Brake. Now I can stop and park on a hill.

 

[Jerryg]

JAH

 

[JayPo]

After the MOM ride last weekend I decided I desperately need a windshield wiper. All of the wipers available are too long for the SuperATV flip windshield. After much research I finally found a 10" wiper. The only issue was the arm was angled and I needed it straight to fit the way I wanted so I straightened it. It fits perfectly. Unfortunately this wiper is like double the cost of all the other wipers but I really wanted a shorter one that fit correctly. @SuperATV you guys need to sell a 10" wiper with a straight arm for some of your not so tall flip-up windshields. This would also have fit my Yamaha Wolverine X2 perfectly as the 13" one I bought from SuperATV is a bit too long.

 

[JenElio]

After the MOM ride last weekend I decided I desperately need a windshield wiper. All of the wipers available are too long for the SuperATV flip windshield. After much research I finally found a 10" wiper. The only issue was the arm was angled and I needed it straight to fit the way I wanted so I straightened it. It fits perfectly. Unfortunately this wiper is like double the cost of all the other wipers but I really wanted a shorter one that fit correctly. @SuperATV you guys need to sell a 10" wiper with a straight arm for some of your not so tall flip-up windshields. This would also have fit my Yamaha Wolverine X2 perfectly as the 13" one I bought from SuperATV is a bit too long.

View attachment 446097

View attachment 446098

$50....... can't hide money!!! 😂😂

 

[JayPo]

Well just like his half day rides, @TripleB went above and beyond with the LED whips I got from him. They are stupid long. Like 4 feet. And they flop around like, uh, well, like something that flops around a lot. So today I cut them down to 3 feet. They're much better now. I might cut them down more but we'll see.

 

[TripleB]

Well just like his half day rides, @TripleB went above and beyond with the LED whips I got from him. They are stupid long. Like 4 feet. And they flop around like, uh, well, like something that flops around a lot. So today I cut them down to 3 feet. They're much better now. I might cut them down more but we'll see.
View attachment 449021

See how long they last before I install mine lol

 

[TripleB]

Well just like his half day rides, @TripleB went above and beyond with the LED whips I got from him. They are stupid long. Like 4 feet. And they flop around like, uh, well, like something that flops around a lot. So today I cut them down to 3 feet. They're much better now. I might cut them down more but we'll see.
View attachment 449021

I figured you would like long floppy things.

 

[MiniRF]

Dirt Road Fabrication. I had them customize it a bit to my liking. I had the fuel bracket centered on the outside. Then instead of metal bars going across the floor on the extended part I had them weld a grill to bolt the cooler bracket down to hold the cooler in place. Two clicks and the cooler comes out. The extended bed also opens and closes.

View attachment 439650

What cooler is this? I like this setup but need more research on cooler size. I definitely want a bigger cooler than the Milwaukee 16qt.