P1000 Key On Power, Illumination, and backup source! - 2016 through 2021 Honda Pioneer 1000 Only

[Hondasxs]

According to Honda Accessory Instructions. Here is the recommended location for Key On Power for the Honda Pioneer 1000 Side by Side!

Honda suggest tapping the 15A Acc Fuse on the output side. Here you will find 2 WHITE with a BLACK STRIPE wires coming out of the output side of the fuse. You will need to untape the wire bunch to access them. It is recommended that you use a posi-tap (not shown) vs the wire tap-ins (shown) for a better error free connection.

 

[Admin]

 

[Hondasxs]

Also,

REVERSE TRIGGER ***
Here is a Reverse trigger with a rear Key-On source, See post 13 - P1000 - Key On Power, Illumination, and backup source! - Honda Pioneer 1000 | The Honda Side by Side Club!

And....
LIGHT ON POWER *Does not apply for the LE model*
Here is a good location for "Light On Power".
Here find the brown wire, this is for the tail lights on! When lights are on it will be hot.
This is good for illumination power of your switches. You can see the posi-tap I have placed on it.

 

[Calvin]

Thx for posting this. Great info. And I need all I can get on electrical stuff.

 

[Ned]

According to Honda Accessory Instructions. Here is the recommended location for Key On Power for the Honda Pioneer 1000 Side by Side!

Honda suggest tapping the 15A Acc Fuse on the output side. Here you will find 2 WHITE with a BLACK STRIPE wires coming out of the output side of the fuse. You will need to untape the wire bunch to access them. It is recommended that you use a posi-tap (not shown) vs the wire tap-ins (shown) for a better error free connection.

View attachment 8398 View attachment 8399 View attachment 8400

Thank you for that information. I hope those watching in Electrical help see it.

 

[Hondasxs]

Thanks.
Your right. Should share it.

 

[ghost]

Yeah, this is awesome. Thanks

 

[ButchersHook]

For those who have the kfi winch mount, on the back the their install instructions it also shows that you should use the 15 amp black white acc wire for winch control power. Also shows best ways to mount the solenoid and where to run power wires.

Not sure why they included in with their winch mount but was helpful when i installed the superwinch.

 

[Springer]

For those who have the kfi winch mount, on the back the their install instructions it also shows that you should use the 15 amp black white acc wire for winch control power. Also shows best ways to mount the solenoid and where to run power wires.

Not sure why they included in with their winch mount but was helpful when i installed the superwinch.

Good to hear. I just ordered he KFI mount and Superwinch Terra 4500, so getting these instructions will be right up my alley!!

 

[Kenjones21]

Honda SxS question for you, The wire harness for the keyed power has some form of clip holding them down , couldn't get a good look at them last night but do they just pop out are is there secret to getting them out.?

 

[fredlp6582]

Thinks, iam fred from golden valley AZ.what does the posi-tap look like, I have the tap-ins.

 

[JACKAL]

Thinks, iam fred from golden valley AZ.what does the posi-tap look like, I have the tap-ins.

See post #2 it is the little red cylinder in the top center of the photo.

 

[Hondasxs]

Ya. That's what I used. Red one with grey end.

 

[Hondasxs]

Here is the correct location for Back up / Reverse power according to OEM instructions for the backup alarm for the Honda Pioneer 1000.
The amp rating for this wire is 15 amps combined including all other items tied into the 15amp "Acc" fuse.

Location includes a positive and a ground trigger.
The WHITE/BLACK STRIP is positive and is "Key On" and can also be used as a Key On source near the rear.
Second wire is GROUND TRIGGER is only active when in Reverse! Be careful, this will read funny with a test light. Test it while in reverse for ground!

Unfortunately, It is a little difficult to access.
Here is the back-up alarm instructions for more details - P1k - Back-Up Alarm Harness - 08Z76-HL4-A00 - Instructiosn | The Honda Side by Side Club!

This plug can been seen by looking up and under just in-front of the rear drivers tire. Looking towards the oil filter and on past to the frame you will see a un-used wire. It will be 2 wires with a white plug.
The plug is sealed with a plug. See back-up alarm harness instructions.

Here are some pictures from a Pioneer 1000-5.

 

[Whiskey1]

Here is the correct location for Back up / Reverse power according to OEM instructions for the backup alarm for the Honda Pioneer 1000.
The amp rating for this wire is 15 amps combined including all other items tied into the 15amp "Acc" fuse.

Location includes a positive and a ground trigger.
Positive is "Key On" and can also be used as a Key On source for the rear.
Ground trigger is only active when in Reverse!

Unfortunately, It is a little difficult to access.
Here is the back-up alarm instructions for more details - P1k - Back-Up Alarm Harness - 08Z76-HL4-A00 - Instructiosn | The Honda Side by Side Club!

This plug can been seen by looking up and under just in-front of the rear drivers tire. Looking towards the oil filter and on past to the frame you will see a un-used wire. It will be 2 wires with a white plug.
The plug is sealed with a plug. See back-up alarm harness instructions.

Here are some pictures from a Pioneer 1000-5. View attachment 8557 View attachment 8558

This is excellent info! I'm going to hunt down that wire and install LED reverse lights! Thank you.

 

[rcarroll]

Does anyone know if there is a reverse trigger wire I can access in the front so I don't have to fish a wire up from the back?

 

[Springer]

Here is the correct location for Back up / Reverse power according to OEM instructions for the backup alarm for the Honda Pioneer 1000.
The amp rating for this wire is 15 amps combined including all other items tied into the 15amp "Acc" fuse.

Location includes a positive and a ground trigger.
Positive is "Key On" and can also be used as a Key On source for the rear.
Ground trigger is only active when in Reverse!

Unfortunately, It is a little difficult to access.
Here is the back-up alarm instructions for more details - P1k - Back-Up Alarm Harness - 08Z76-HL4-A00 - Instructiosn | The Honda Side by Side Club!

This plug can been seen by looking up and under just in-front of the rear drivers tire. Looking towards the oil filter and on past to the frame you will see a un-used wire. It will be 2 wires with a white plug.
The plug is sealed with a plug. See back-up alarm harness instructions.

Here are some pictures from a Pioneer 1000-5. View attachment 8557 View attachment 8558

I used this info to wire up my backup lights. I chose to have them come on when in reverse, regardless if the headlights are on or not as long as the ignition is on. I was able to simply use the two wires as hot and ground, and ran them to the lights. Easy peezey.
Thanks HONDASXS, your my hero!

 

[rubicon05]

I used this info to wire up my backup lights. I chose to have them come on when in reverse, regardless if the headlights are on or not as long as the ignition is on. I was able to simply use the two wires as hot and ground, and ran them to the lights. Easy peezey.
Thanks HONDASXS, your my hero!

What wires did you tap into? This is exactly what I'd like to do. Thanks

 

[Springer]

What wires did you tap into? This is exactly what I'd like to do. Thanks

These two

 

[Hondasxs]

@PioneerPete
lol...
All fun-n-games. haha.

 

[PioneerPete]

I have a big heart and care about everyone... even grumpy old men! lol I guess Buffett said it best, "if we couldn't laugh, we'd all go insane".