P1000m3 Tot's Rig

[ghost]

Looking good.
That accessory list is great but what with the floor mats? I've never seen them and I couldn't imagine why I would want them. Maybe they keep the water from sloshing in around the pedals?

 

[Admin]

 

[Tot]

Thanks! I still have a ways to go.

I was really disappointed in them. They were thinner than I was expecting and it's all one mat. According to the instructions I have to drill holes in the floor to pin them down. I'll get some pictures of it later this morning

 

[Tot]

There wasn't a really good way to get pictures of the floor mat, but I did get it in.

 

[Tot]

Had to drill about 8 holes in the floor to pin it in. The instructions said to take the floor out because there may have been important lines run where the holes needed to go. Well, I didn't remove it, I crawled under it to see and nothing was in the way. I pulled out a couple pin in the floor and reused them when I put the mat down. I think there was just 1 on each side and 2 in the middle that had to be pulled out and reused.

 

[Tot]

Got a chance to ride around the farm and my neighbors farm, put 18 miles on that ride. Took it down a gravel road and found the raddle spots. I put tape on the doors and tried it on the bed, but it made the bed hard to close. Anyone have tips besides tape for the bed raddling?

 

[CashMoney]

Got a chance to ride around the farm and my neighbors farm, put 18 miles on that ride. Took it down a gravel road and found the raddle spots. I put tape on the doors and tried it on the bed, but it made the bed hard to close. Anyone have tips besides tape for the bed raddling?

You should be able to adjust the part it latches too up or down. At least I think my salesman said that. I got lucky my dealership adjusted all that before I even picked it up and never had any rattles

 

[Tot]

You should be able to adjust the part it latches too up or down. At least I think my salesman said that. I got lucky my dealership adjusted all that before I even picked it up and never had any rattles

Dang lucky you! Mine isn't bad, I had to adjust the passenger door and the bed is all. The steering wheel is turned to the right, but the machine tracks straight down the road.

 

[CashMoney]

I've been pretty impressed with their pre inspection. They seemed to check most things properly.

 

[Tot]

Put about 25+ miles today and I'm in love with this thing! Only one bad thing happened while riding, Beau decided he needed to poop... that was a mess.

 

[Tot]

Got the 2.0s sold this afternoon!



I'm thinking of waiting to buy new trail tires and going ahead and buying the truck tires now since I still have the stockers on the steel wheels to run.

 

[Tot]

Purchased 15x7 STI HD 4s today. Friday I should be buying tires

 

[Tot]

Look what came in today!!

 

[nbomar]

Look what came in today!!

View attachment 11056

So is it installed yet?

 

[Tot]

So is it installed yet?

Not yet. Tomorrow or Thursday it will be. It doesn't look like much so I might try to knock it out after work

 

[pct]

Got a chance to ride around the farm and my neighbors farm, put 18 miles on that ride. Took it down a gravel road and found the raddle spots. I put tape on the doors and tried it on the bed, but it made the bed hard to close. Anyone have tips besides tape for the bed raddling?

there are adjustments on about all of the latches the bed ones are a little touchie just make sure that it latches all the way mine the first time you could jerk up and it would come unlatched

 

[Tot]

there are adjustments on about all of the latches the bed ones are a little touchie just make sure that it latches all the way mine the first time you could jerk up and it would come unlatched

I noticed that. I went to shut the bed and a few moments later it was up again

 

[pct]

I had one side to tight just had to play with them to get it to latch

 

[Tot]

Lookie what came in today!!

 

[Tot]

2.5 inch Highlifter lift.
Tapatalk - Trending Discussions About Your Interests
2.5 inch Highlifter lift.

 

[Tot]

Also want to confirm that 4x137 pattern will fit the Pioneer 1000s. At least the 3 Seaters.